Manual Finlux 40F8030-T (page 38 of 49) (English)

500520

Zoom out

Zoom in

1/49

English - 37 -

Tips

Screen Care: Clean the screen with a dry, soft cloth.

Do not use abrasive solvents as they may damage the

coating layer of the TV screen. For your safety, unplug

the mains plug when cleaning the set. When moving

the TV, hold it properly from the bottom part.

Image Persistence: Please note that ghosting may

occur while displaying a persistent image. LED TVs’

image persistence may disappear after a short time.

Try turning off the TV for a while.

To avoid this, do not leave the screen in still picture

for extended periods.

No Power: If your TV system has no power, please

check the main power cable and connection to the

mains socket outlet.

Poor Picture: Have you selected the correct TV

system? Is your TV set or house aerial located too

close to a non-earthed audio equipment or neon

lights, etc.? Mountains or high buildings can cause

double pictures or ghost images. Sometimes you can

improve the picture quality by changing the direction

of the aerial. Is the picture or teletext unrecognisable?

Check if you have entered the correct frequency.

Please retune the channels. The picture quality may

degrade when two peripherals are connected to the

TV at the same time. In such a case, disconnect one

of the peripherals.

No Picture: Is the aerial connected properly? Are the

plugs connected tightly to the aerial socket? Is the

aerial cable damaged? Are suitable plugs used to

connect the aerial? If you are in doubt, consult your

dealer. No Picture means that your TV is not receiving

a transmission. Have you selected the correct button

on the remote control? Try once more. Also make sure

the correct input source has been selected.

Sound: You can not hear any sound. Did you perhaps

mute the sound, pressing the button? Sound is

coming from only one of the speakers? Is the balance

set to one extreme? See Sound Menu.

Remote Control: Your TV no longer responds to the

remote control. Perhaps the batteries are exhausted.

If so you can still use the local buttons on the TV.

Input Sources: If you cannot select an input source,

it is possible that no device is connected. Check

the AV cables and connections if you have tried to

connect a device/

Recording Unavailable: To record a programme, you

should rst connect a USB disk to your TV while the

TV is switched off. You should then switch on the TV to

enable recording feature. Otherwise, recording feature

will not be available. If you cannot perform recording,

try switching off the TV and then re-inserting the USB

device while the TV is switched off.

USB Is too Slow: If “USB is too slow” message is

displayed on the screen while starting a recording,

try restarting the recording. If you still get the same

error, it is possible that your USB disk does not meet

the speed requirements. Try connecting another

USB disk.

Picture Breakup: If whilst watching DTV you

experience picture or sound disruptions then please

retune your TV using “First Time Installation” and

make sure you select the correct region/transmitter

when prompted by the “Choose Region” on screen

message. Please note regional selection can only be

made if “First time Installation” is used.

TV Switches Randomly to Stand-By: The TV by

default will switch back to standby after 4 hours if the

TV remote is not used, this is most likely to occur if you

are you are using an external set-top box as a signal

source or you are out of the TV room. This power

saving feature can be switched off or the activation

time extended or reduced via the menu “Settings->

Other Settings -> Auto TV OFF”. The TV will also

return to stand-by if the aerial signal is lost for more

than 5 minutes.

Dark Picture: When the TV is rst switched on the

back lights brightness is reduced, this is normal

operation and the brightness will increase to the

running level within a few minutes. Please note when

“Backlight” is set to “Auto” the backlight brightness will

change with picture content.

Wireless Network Not Available: Ensure that the

firewalls of your network allows the TV wireless

connection. “Veezy 100” usb wi dongle should be

plugged properly (if available). If the wireless network

does not function properly, try using the wired network

in your home. Refer to the Wired Connection section

for more information on the process.

If the Net TV does not function, check the modem

(router) rst. If the router does not have a problem,

check the internet connection of your modem.

Try searching for wireless networks again, using the

Network Settings menu screen.

Connection is Slow: See the instruction book

of your wireless modem to get information on the

internal service area, connection speed, signal quality

and other settings. You need to have a high speed

connection for your modem.

Distruption during playback or slow reactions:

You could try the following in such a case: Keep

at least three meters distance from microwave ovens,

mobile telephones, bluetooth devices or any other

Wi-Fi compatible devices. Try changing the active

channel on the WLAN router.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Finlux 40F8030-T in the language / languages: English as an attachment in your email.

The manual is 11,13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Finlux 40F8030-T Manual

Product: