456444
7
Zoom out
Zoom in
Previous page
1/11
Next page
Cod. 710.056.02.00 – Rev. 04 – 07.06.2001
ENGLISH
page 18 of 63
3.6 ABNORMALITY SIGNALLING
The controller is capable to recognise certain types of abnormities of the drying circuit. In case of this occurrence, an
alarm message will blink on the display, alternated with the current dew – point value.
MESSAGE (BLINKING) CAUSE
HtA
Dew - point > (E1 + E6) for a time equal to the E7 preset value
LtA
Dew - point < (E1 - E38) for a time equal to the E7 preset value
PF1
Interruption or short circuit on the PTC probe input line
All alarm messages disappear immediately when the relevant cause ceases, except the PF1 message, which,
in addition, requires to cycle ON/OFF the machine by means of the mains knife switch.
PF1 has priority over all other messages.
3.7 DESCRIPTION AND STANDARD VALUE OF THE CONDENSATE DISCHARGE SETTINGS
PARAMETR DESCRIPTION RANGE SET VALUE
E8
Interval between condensate
discharges
1 ÷ 999 (min)
1
E9
Time required for condensate
discharge
1 ÷ 999 (sec)
2
WARNING FOR USER:
IT’S FORBIDDEN TO MODIFY THE OTHER CONFIGURATION PARAMETERS OF THE ELECTRONIC
CONTROLLER WITHOUT THE AUTHORIZATION OF THE SUPPLIER.
4. MAINTENANCE, TROUBLESHOOTING AND DISMANTLING
4.1 MAINTENANCE
Before attempt any maintenance operation, make sure that
1. No parts of the system is under pressure.
2. No parts of the system is electrically powered.
WEEKLY OR EVERY 40 HOURS OF OPERATION
Verify that the temperature indicator on the display of the control panel is positioned within the
green section (dew point about 3°C).
Check visually for proper and regular operation of the condensate drainage.
MONTHLY OR EVERY 200 HOURS OF OPERATION
Clean the condenser with a compressed air jet, taking care not to damage the aluminium wings of
the cooling battery.
Clean the pre-filter of the condensate drainage system to remove eventual impurities present on
the internal mesh. Be extremely careful during reassembling (se figure below)
At the end of these operations, check the dryer for proper operation.
YEARLY OR EVERY 2000 HOURS OF OPERATION
Clean the condenser with a compressed air jet and wash the winged assembly with running water,
operating carefully not to damage it, in order to remove eventual scaling or deposits.
Check for damages the flexible condensate drainage hose, and replace it if necessary.
Check for proper tightness and stability all the connecting tubing.
At the end of the over listed operations, check the dryer for proper operation
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Finicompressors Artic 134-9 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Finicompressors Artic 134-9 in the language / languages: English as an attachment in your email.

The manual is 0,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Finicompressors Artic 134-9

Finicompressors Artic 134-9 User Manual - German - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info