456446
11
Zoom out
Zoom in
Previous page
1/11
Next page
Cod. 710.056.02.00 – Rev. 04 – 07.06.2001
ENGLISH
page 22 of 63
7. INTELLIDRAIN
7.1 GENERAL
IntelliDrain is the new discharger applicable to any compressed air systems, where there is the necessity to
eliminate the condensate without wasting compressed air.
Easy to clean and compact, it definitely eliminates the problems concerning air consumption and acoustic
emission of the timed drains.
It can be applied to tanks, separators, dryers, filters, air compressors, etc.
IntelliDrain starts automatically, without the need of any adjustment. The condensate discharge occurs
thanks to the use of a electronic sensor, which detects the amount of condensate in the integrated water
collecting tank.
The level sensor drives the start and the duration of the drainage, so preventing any wasting of compressed
air.
The electric panel consists of the following components:
(1) Green LED electric power on
(2) Red LED condensate drain active
(3) KEY drainage TEST
2 3
1
OUT
IN
7.2 INSTALLATION
The discharger must be always installed under the drainage level of the tank to be drained, and as close as
possible to the drain attachment.
Avoid the formation of siphons at the discharger inlet: the condensate reaching the discharger must allow
the reflux of air bubbles towards the top. Moreover, the connection tubing between the drain of the tank and
the IntrelliDrain device must be of a proper size (minimum suggested size 3/8”).
To prevent possible malfunctioning of the discharger, we suggest to use the accessories, i.e. network filters
and valves, supplied by the manufacturer,
Condensate can be discharged freely or through a drainage tubing having an adequate size. The draining
tube can also be some meters upwards.
At the end of the installation, put the plant under pressure and press repeatedly the TEST key to eliminate
the air bubbles contained in the inlet unions lf the discharger.
7.3 MAINTENANCE AND MALFUNCTIONING TREATMENT
Before attempting any maintenance operation, insulate the discharger from pressure and electrical
supply. We suggest to frequently remove and clean the mesh filter on the discharger inlet, specially in
the first days following the installation, until the complete removal from the line of rust, dirt, powders,
etc.
Should the discharger not correctly operate, try to act on the TEST key to clean the mesh filter.
Never remove the discharger body. Should the malfunctioning persist, contact your preferred reseller.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Finicompressors Artic 134-25 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Finicompressors Artic 134-25 in the language / languages: English as an attachment in your email.

The manual is 0,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Finicompressors Artic 134-25

Finicompressors Artic 134-25 User Manual - German - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info