Manual Fimer Windy (page 4 of 28) (Dutch)

688774

Zoom out

Zoom in

1/28

WARNING SYMBOLS

CAUTION

DANGER

(Indicating a hazard that could cause injury or damage)

DANGER

OF FIRE OR EXPLOSION.

Indicating that eye protection is required to avoid

burns and eye damage.

TOXIC GAS

Indicating the risk of toxic gas hazards

HOT SLAG

Indicating the risk of being burned by hot slag

EYE PROTECTION

Indicating that eye protection is required to avoid flying debris

ELECTRIC SHOCK

(Indicating the danger of electric shock)

DANGER COMPRESSED GAS

Indicating the risk of injury or death in the event of improper hand-

ling or maintenance of compressed gas cylinders or regulators

IMPORTANT INFORMATION

Indicating the precautions to be taken when installing and

using the unit.

DISPOSAL

INFORMATION

FIRE

PRECAUTIONS

SAFETY WARNINGS

This equipment is designed solely for industrial or

professional use. As such, only experienced or ful-

ly-trained people should use the equipment. The user

and/or owner is responsible for ensuring inexperienced person-

nel does not have access to the equipment.

The safety information contained in this manual is a guide to

ensure you are not subjected to unnecessary risks. However,

the operator must be competent and careful at all times.

Fimer SpA declines all responsibility for injury or dama-

ge caused by inexperienced, improper or neglectful use

of its equipment.

A workman must look after his tools carefully ! Remember that

any tool or equipment can become a hazard if it is not looked

after properly.

Equipment in a state of disrepair or neglect can be dangerous. If it

does not operate properly or overheats, the electricity supply should

be removed immediately and the unit should be returned to the sup-

plier for repair.

All equipment connected to electric power supplies can be dan-

gerous if the manufacturers instructions are not read and obser-

ved. Read, understand and observe these safety instructions

to reduce the risk of death or injury from electric shock. Ensure that

even bystanders are aware of, and understand, the dangers that exi-

st in the welding area.

Read this manual carefully before using your Welder.

You can then do a better and safer job.

By reading this manual you will learn more about the

possibilities, limitations and potential dangers of welding.

Retain this manual for the entire life of the equipment. It should be

kept within the operator’s reach at all times.

Fires and explosions can seriously injure or cause dama-

ge ! Read, understand and observe all safety warnings

to reduce the risk of death or injury from fire or explo-

sion. Pay particular attention to the fact that even bystanders should

be aware of, and understand, the dangers existing in the welding area.

Remember that welding, by nature, produces sparks, hot spatter, mol-

ten metal drops, hot slag and hot metal parts that can cause fires, can

burn skin and damage eyes.

Arc rays can damage your eyes and burn your skin ! Read,

understand and observe all safety warnings to avoid dama-

ge from arc rays. Pay particular attention to the fact that

even bystanders should be aware of, and understand, the dangers exi-

sting in the welding area. Wear a protective mask and make sure bystan-

ders do the same.

Fumes, toxic gases and vapours can be harmful ! Read,

understand and observe all safety warnings to avoid harm

from toxic welding gases. Pay particular attention to the fact that even

bystanders should be aware of, and understand, the dangers.

Carelessness while using or maintaining the compres-

sed gas cylinders or regulators can injure or kill the

operator and/or bystanders ! Read, understand and observe all safety

warnings to avoid the dangers of compressed gas. Pay particular

attention to the fact that even bystanders should be aware of, and

understand, the dangers.

HIGH VOLTAGE

The unit carries potentially lethal voltage.

The high voltage areas of the equipment have been segregated

and can be reached only by using tools that are not provided with the

Welder.

All maintenance or repair operations requiring access to such areas may

only be performed by Fimer-trained technicians.

FOREIGN OBJECTS

Never block the air vents with foreign objects and avoid

any contact with liquids. Clean using just a dry cloth. The-

se safety precautions apply even when the unit is switched off.

CABLE GAUGES

Check that all cables are appropriately gauged for

the input power required by your specific Welder.

This precaution applies also to extension cables, if used. All extension

cables must be straight. Coiled cables can overheat, becoming dange-

rous. Twisted or coiled cables can also cause Welder malfunction.

WEIGHT LOADS

The upper part of the Welder was not designed to with-

stand heavy loads. Never stand on the unit.

INSTALLATION

INSTRUCTIONS

OPERATING

INSTRUCTIONS

UNPACKING

INSTRUCTIONS

4 van 28

ou trouve ton les telecommandes windy car introuvable en france ils vendent les clims mais pas les télécommande !!!!!!!! Submitted on 27-8-2020 at 15:13
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Fimer Windy in the language / languages: Dutch as an attachment in your email.

The manual is 6,8 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Fimer Windy

Fimer Windy User Manual - French - 18 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Fimer Windy Manual

Product: