499201

Festool TURBO 7501 Manual

12
Zoom out
Zoom in
Previous page
1/54
Next page
12
The extraction system must not be set up in
rooms where there is a risk of explosion or
in the proximity of fl ammable substances
(e.g. solvents).
After unpacking, the extraction system can be
transported on a fork-lift truck or pallet truck. In
doing so, ensure that both transverse struts (front
and rear) of the sub-frame are seated securely on
the forks of the transport vehicle. Make sure that
the majority of the weight is located on the side of
the electric control panel.
To prevent the impermissible heating of the extrac-
tion system, the system must be located in a room
with a suffi cient supply of air.
2.2 Electrical connection
The operating voltage specifi ed on the
rating plate must match the voltage of the
mains power!
- For safety reasons, only operate the machine
using a totally earthed socket.
If the suction turbines turn in the direction opposite
to the specifi ed direction (3.1) during installation,
two of the phases of the connector (1.12/2.11) must
be swapped. This work may only be performed by
a qualifi ed electrician!
The control line (12 V~), for automatically switching
ON/OFF the extraction system, must be connected
to the connector (1.10/2.13).
2.3 Compressed air connection
For fi lter cleaning, fi ltered and dry compressed
air with a fl ow pressure of 6 bar is required at the
compressed air connection (1.9, 2.12). A pressure
regulator with fi lter and water separator must be
connected to this. Use the pressure regulator to
set a pressure of 6 bar.
A minimum input pressure of 6 bar is required
at the pressure reducer to ensure that the hub
rotates adequately, while 4 bar is required di-
rectly at the hub.
The turbine performs one cleaning cycle every
minute for 10 seconds. Approx. 350l of air is
required during each cleaning cycle. We recom-
mend installing a buffer container with a mini-
mum volume of 150l upstream of the turbine to
ensure the required air pulse is generated.
3 Initial operation
When in operation, the rotary switch (1.13/2.14)
must be in the AUTO position.
The extraction system is made ready for operation
by means of the main switch (1.1/2.1) (Ready for
operation = I, Off = O).
The control lamp (1.2/2.2) lights up when the sys-
tem is ready for operation.
The extraction fan only starts up when the extrac-
tion system is ready for operation and when it
receives a signal from the external control line.
Depending on the installation and pipe routing, this
signal can be triggered by switching on a connected
sander or opening a sliding valve.
The suction turbine sucks in air/dust through the
suction spout (1.11/2.6). The fi ltered air fl ows out
again through the outgoing air spout (1.8/2.11).
4 Filter system
The extraction system has an automatic filter
cleaning system based on the principle of the
counterfl ow process. The fi lter is cleaned regularly
during operation and after shutdown by means of
pressure surges.
4.1 Emptying and replacing the dust bag
During the following procedure, take care
not to raise dust more than is unavoid-
able.
- Turn off the main switch (1.1/2.1).
- Open the two clips (1.5/2.7) and pull out the dust
bag container (1.7/2.9).
- Close the dust bag (1.6/2.8) so that it is dustproof,
and dispose of it in accordance with statutory
regulations.
- Check the seal (3.2) for damage. Replace a dam-
aged seal immediately.
- Insert a new dust bag (4.1). Make sure that the
dust bag is seated at the edge of the dust bag
container and that the two openings (4.2) of the
dust bag are located in the dust bag container.
- Press the air out through the two openings (4.2)
located between the dust bag and dust bag con-
tainer. The dust bag must be located at the inner
wall of the dust bag container so that it is not
pulled upwards by the ventilating pressure cre-
ated when the extraction system is switched on.
- Insert the dust bag container and close the two
clips (1.5/2.7). The upper edge of the dust bag
container must make full contact with the seal
(3.2). If required, the clamping power can be ad-
justed using the screws on the clips (1.5/2.7).
4.2 Changing the fi lter
During the following procedure, take care
not to raise dust more than is unavoid-
able.
- Turn off the main switch (1.1/2.1).
- Only for Turbo 7501: open the screws (1.3) and
take off the cover (1.4).
- Only for Turbo 4001 and 3091: open the two clips
(2.5).
- Take off the extraction pipe (5.1/2.3) and com-
pressed air line (5.2/2.4).
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool TURBO 7501 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool TURBO 7501 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info