497613

Festool TS 75 EQ Manual

19
Zoom out
Zoom in
Previous page
1/139
Next page
–Always observe that the guard is covering
the blade before placing the saw down on
bench or floor. An unprotected, coasting
blade will cause the saw to walk back
wards, cutting whatever is in its path. Be
aware of the time it takes for the blade to
stop after the switch is released.
Riving knife function
–Use the appropriate saw blade for the riv
ing knife. For the riving knife to function,
the body of the blade must be thinner than
the riving knife and the cutting width of the
blade must be wider than the thickness of
the riving knife.
–Adjust the riving knife as described in this
instruction manual. Incorrect spacing,posi
tioning and alignment can make the riving
knife ineffective in preventing kickback.
–For the riving knife to work, it must be en
gaged in the workpiece. The riving knife is
ineffective in preventing kickback during
short cuts.
–Do not operate the saw if the spacer
wedge is bent. Even the slightest problem
can cause the guard to close more slowly.
2.3 Safety instructions for the pre-
assembled saw blade
Usage
– The maximum speed specified on the saw
blade must not be exceeded and the speed
range must be adhered to.
– The pre-installed saw blade is only de
signed for use in circular saws.
– Proceed with extreme care when unpack
ing, packing and handling the tool (e.g. in
stalling it in the machine). There is a risk of
injury from extremely sharp cutting edges!
– When handling the tool, wearing safety
gloves provides a more secure hold of the
tool and further reduces the risk of injury.
– Circular saw blades with cracked bodies
must be replaced. Repair is not permitted.
– Circular saw blades with a combination de
sign (soldered saw teeth) with saw tooth
thickness smaller than 1 mm must no lon
ger be used.
– Do not use tools with visible cracks or blunt
or damaged cutting edges.
Installation and mounting
– Tools must be clamped in such a way that
they cannot come loose during operation.
– When assembling the tools, it must be en
sured that the clamping takes place on the
tool hub or the clamping surface of the
tool, and that the cutting edges do not
come into contact with other components.
– Do not lengthen the key or tighten by hitting
with a hammer.
– The clamping surfaces must be cleaned to
remove contamination, grease, oil and wa
ter.
– Clamping screws must be tightened ac
cording to the manufacturer's instructions.
– Only securely installed rings, e.g. rings that
have been pressed in or those that are held
in position by an adhesive bond, may be
used to adjust the hole diameter of circular
saw blades to the spindle diameter of the
machine. The use of loose rings is not per
mitted.
Service and maintenance
– Repairs and sanding work may only be car
ried out by Festool customer service work
shops or experts.
– The tool design must not be changed.
– Deresinify and clean the tool regularly
(cleaning agent with pH between 4.5 and 8).
– Blunt edges can be resharpened on the
clamping surface to a minimum cutting
edge thickness of 1 mm.
– Only transport the tool in suitable packag
ing – risk of injury!
2.4 Further safety instructions
–
Wear suitable personal protective equip
ment: Ear protection, protective goggles,
dust mask for work that generates dust,
protective gloves for working with rough
materials and for changing tools.
–Harmful/toxic dust may be produced dur
ing your work (e.g. paint containing lead,
certain types of wood or metals). Contact
with or inhalation of this dust may pose a
risk for the operating personnel or persons
in the vicinity. Comply with the safety regu
lations that apply in your country.
– Wear a P2 respiratory mask to protect
your health. In enclosed spaces, ensure
that there is sufficient ventilation and con
nect a mobile dust extractor.
English
19
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool TS 75 EQ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool TS 75 EQ in the language / languages: All languages as an attachment in your email.

The manual is 2.42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Festool TS 75 EQ

Festool TS 75 EQ User Manual - English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 102 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info