383528

Festool ts 55 q Manual

17
Zoom out
Zoom in
Previous page
1/94
Next page
17
stop notches along in 1 mm-steps).
The sawing unit can now be pressed down to the
set cutting depth.
A grub screw (M4x8 to M4x12) can be screwed into
the hole [2-2] on the cutting depth stop. By turning
the grub screw, the cutting depth can be set even
more exactly (± 0.1 mm).
4.3 Cutting angle
The sawing unit can be swivelled between 0° and
45°:
- Loosen rotary knobs [2-4, 2-6],
- Swivel sawing unit to the desired cutting angle
[2-5],
- Retighten rotary knobs.
Note: both end positions (0° and 45°) are set at
the factory and can be readjusted by the aftersales
service team.
4.4 Changing the saw blade
- Before changing the saw blade, set the machine
to the 0° position.
- Move lever [3-2] as far as it will go,
- Push switch lock [3-1] up and push sawing unit
down until it locks into place,
- Loosen screw [3-4] with Allen key [3-3],
- Remove saw blade,
- Clean fl ange [3-8, 3-10],
- Insert new saw blade.
The direction of rotation of the saw blade
[3-9] and the machine [3-7] must be the
same.
- Insert outer fl ange [3-10] such that the locking
pins engage into the notches on the inner fl ange
[3-8].
- Tighten screw [3-4],
- Put lever [3-2] back.
4.5 Setting the spacer wedge
- Move lever [3-2] as far as it will go,
- Push switch lock [3-1] up and push sawing unit
down until it locks into place,
- Loosen screw [3-6] with Allen key [3-3],
- Set spacer wedge [3-5] as shown in diagram 3,
- Tighten screw [3-6],
- Put lever [3-2] back.
4.6 Dust extraction
Always connect the machine to a dust ex-
tractor.
A Festool dust extractor with an extractor hose di-
ameter of 36 mm or 27 mm (36 mm recommended
due to the reduced risk of clogging) can be con-
nected to the rotating extractor connector [4-1]
4.7 Mounting the splinterguard
The splinterguard (accessories) signifi cantly im-
proves the quality of the cutting edge of the sawn
workpiece on the upper side for 0° cuts.
- Attach splinterguard [5-1] onto the protective
cover,
- Place machine onto the workpiece or the guide
rail,
- Press splinterguard down until it sits on the work-
piece and tighten it with the rotary knob [5-2].
- Saw splinterguard in (machine to maximum cut-
ting depth and speed range 6)
5 Working with the machine
Always secure the workpiece in such a
manner that it cannot move while being
sawed.
The machine must always be held with
both hands by the designated handles [1-
1, 1-7].
Always push the machine forwards [1-2],
never pull the machine backwards towards
you.
Adapt the fast-feed speed to prevent the
cutters on the saw blade from overheating
and prevent plastic materials from melting
during cutting.
5.1 Sawing along a scribe mark
The cutting indicator [4-3] displays the cutting line
for 0° and 45° cuts (without guide rail).
5.2 Sawing sections
Place the machine with the front part of the saw
table on the workpiece, switch the machine on,
press it down onto the set cutting depth and push
it forward in the cutting direction.
5.3 Sawing cut outs (plunge cuts)
In order to avoid kickbacks, the following instruc-
tions absolutely must be observed when plunge
cutting:
- The machine must always be placed with the rear
edge of the saw table against a fi xed stop.
When working with a guide rail, the machine must
be positioned against the kickback stop [1-4],
which is clamped on the guide rail.
- The machine must always be held securely with
both hands and only plunged slowly.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool ts 55 q at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool ts 55 q in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian as an attachment in your email.

The manual is 1,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info