778504
27
Zoom out
Zoom in
Previous page
1/150
Next page
Always use original Festool spare
parts. Order no. at:
www.festool.co.uk/service
EKAT
1
235
4
The tool is equipped with special self-discon
necting carbon brushes. If they wear out, the
power supply is disconnected automatically and
the tool stops.
Observe the following instructions:
Damaged safety devices and parts, such as
a faulty lever for changing tools [1-5], must
be properly repaired or replaced in a recog
nised specialist workshop, unless otherwise
indicated in the operating manual.
Check the condition and fault-free function
ing of the recuperating springs, which push
the entire drive mechanism bearing into the
upper protected end positions.
To ensure constant air circulation, always
keep the cooling air openings in the housing
clean and free of blockages.
Use an extractor on all openings in order to
remove wood chips and splinters from the
power tool. Never open the protective
lid [1-18].
When working with plaster- and cement-
bonded fibreboards, clean the tool particu
larly thoroughly. Clean the vents of the
power tool and on/off switch using dry, oil-
free compressed air. Otherwise, gypsum
dust deposits may build up inside the power
tool's housing and on the on/off switch and
harden when exposed to humidity. This may
impair the switching mechanism
9.1 Reconditioned saw blades
You can use the adjusting screw [8-1] to pre
cisely set the cutting depth for reconditioned
saw blades.
Set the cutting depth stop [8-2] to 0 mm
(with guide rail).
Unlock the saw unit and push it downwards
as far as the stop.
Screw the adjusting screw [8-1] in until the
saw blade comes into contact with the
workpiece.
9.2 Saw table wobbles
The saw table must be on an even surface
when adjusting the cutting angle.
If the saw table wobbles, the setting must be
implemented again (Section 7.3).
10 Accessories
Always use accessories and consumable mate
rials approved by Festool. See Festool cata
logue or www.festool.com.
The power tool may become unsafe and lead to
serious accidents if other accessories and con
sumables are used.
In addition to the accessories described,
Festool also provides a comprehensive range of
system accessories that allow you to use your
machine more effectively and in diverse appli
cations, e.g.:
Parallel stop, table widener PA-TS 55
Side-mounted cover, false joint ABSA-TS
55
Kickback stop FS-RSP
Parallel stop FS-PA and guide extension
FS-PA-VL
Multifunction table MFT/3
10.1 Saw blades, other accessories
In order to saw different materials quickly and
cleanly, Festool offers saw blades for all appli
cations and these are specially designed for
your Festool saw.
10.2 Guide system
The guide rail enables you to make clean, accu
rate cuts while simultaneously protecting the
surface of the workpiece from damage.
In conjunction with the extensive range of ac
cessories, exact angled cuts, mitre cuts and fit
ting work can be completed with the guide sys
tem. The option of attaching the guide rail se
curely using clamps [9-5] ensures safer work
ing conditions.
Adjust the guide play between the saw table
and the guide rail using the two adjustable
jaws [9-1].
Bed in the splinter guard [9-3] before using
the guide rail for the first time:
Set the machine speed to 6.
Place the machine at the rear end of the
guide rail together with the complete guide
plate.
Switch on the machine.
Push down the machine slowly to the max.
preset cutting depth and cut along the full
length of the splinter guard without stop
ping.
The edge of the splinter guard now corresponds
exactly to the cutting edge.
Position the guide rail for sawing the
splinter guard on a test piece of wood.
English
27
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool TS 55 FEQ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool TS 55 FEQ in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4.92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info