778625
14
Zoom out
Zoom in
Previous page
1/76
Next page
6 Commissioning
6.1 Belt clip [1-10]
The belt clip allows the power tool to be attach
ed to work attire for brief periods. It can be at
tached to the right or left of the power tool us
ing a screw [1a].
6.2 Switching on/off [1-6]
Press = ON, release = OFF
CAUTION
Risk of injury
Do not look directly into the LED light. [4]
The LED light [1-4] lights up when the on/off
switch [1-6] is pressed.
Set the rotational direction switch/safety lock
[1-8] to the centre position to lock the on/off
switch.
7 Battery pack
7.1 Changing the battery pack [2]
Press both buttons at the same time [1-1]
and pull the battery pack forwards and out
of the device.
Insert the new, fully charged battery pack
so that it clicks into place on the bottom of
the tool.
Follow the instructions enclosed with the
charger in order to charge the battery pack.
7.2 Capacity indicator
The capacity display [1-3] indicates the charge
of the battery pack for approx. 2 seconds after
the button [1-2] is pressed:
70–100%
40–70%
15–40%
< 15%*
* Recommendation: Charge the battery pack
before any further use.
Further information about the charger and
battery pack with capacity indicator can be
found in the corresponding operating
manual.
8 Settings
CAUTION
Risk of injury
Only adjust the settings when the power
tool is switched off.
8.1 Changing direction of rotation [1-8]
Switch to the left = clockwise rotation
Switch to the right = counterclockwise rota
tion
8.2 Setting the speed/stroke rate
Once it has been switched on, the tool will auto
matically revert to the gear/mode that was last
selected.
The T-mode is recommended when using self-
tapping drill screws.
Press the gear switch [1-5] as many times
as necessary to select the desired gear/
mode.
One speed LED is lit
= 1st gear
Two speed LEDs are lit
= 2nd gear
Three speed LEDs are lit
= 3rd gear
T-mode LED is lit
= T-mode
Drive in some test screws first to check the
correct gear setting.
8.3 T-mode
Operating mode for driving small self-tapping
drill screws (< 5 x 20 mm) into sheet metal with
wooden substructures. After drilling through
the sheet metal, the speed is automatically re
duced to enable safe screwdriving.
9 Tool holder, attachments
WARNING
Risk of injury
Remove the battery pack from the power
tool before performing any work on the
power tool.
English
14
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool TID 18 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool TID 18 in the language / languages: All languages as an attachment in your email.

The manual is 1.67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info