Manual Festool TDK 15 6 (page 13 of 62) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

497587

Zoom out

Zoom in

1/62

- By keeping the battery pack in a ready for use

charger, the battery pack will be kept in a state

of readiness by ﬂ oat charging conservation.

- Do not keep discharged battery pack (maxi-

mum one month) attached to charger whene-

ver charger is detached from the power supply

(danger of deep discharging).

- A new battery pack or a battery pack not used

for a longer period of time reaches it full ca-

pacity after about 5 charging and discharging

cycles.

- Battery packs should, before charging, be fully

discharged if possible.

Continuous starting of the charging process

shortens the lifespan of the batteries.

- A considerably reduced time of operation per

charging shows that the battery pack is used

up an should be replaced by a new one.

- NiCd battery packs that are not used for lon-

ger periods should be stored in a discharged

state.

Special instructions for NiMH battery

packs:

- The output of NiMH battery packs drops no-

ticeably at ambient temperatures below 0° C

or above 45° C.

- Do not overload the tool (do not load the tool

excessively so that it comes to a standstill).

- Even if NiMH battery packs are not used, re-

charge them approx. every 4 months so that

they retain their full capacity.

- NiMH battery packs should be left for 60 min.

in the charger after every 10th fast charge

to compensate any differences in capacity

between the cells.

- Because NiMH battery packs discharge auto-

matically, store them preferably at ambient

temperatures of between 0° C and 25° C.

6.1 Changing carbon brushes

If the carbon brushes have worn to a length of

less than 6 mm, this may reduce the perfor-

mance of the machine or cause the machine

to stop. In this case, the brushes (4.2) should

be replaced.

- Unscrew the cover (4.4) and remove the worn

brushes.

- Push in the retaining plate (4.3) on the new

carbon brushes until it latches into the notches

(4.1) and screw the covers back on.

- Operate the machine in idling state for a few

minutes so that the carbon brushes attain

optimal contact.

7 Recycling battery packs

Never throw spent battery packs

into domestic waste containers!

Return spent or defective battery packs to dea-

lers, the Festool after-sales service department

or approved waste disposal facilities. This en-

sures that they are correctly recycled.

8 Warranty

Our equipment is under warranty for at least 12

months with regard to material or production

faults in accordance with national legislation.

In the EU countries, the warranty period is 24

months (an invoice or delivery note is required

as proof of purchase). Damage resulting from,

in particular, normal wear and tear, o-verloa-

ding, improper handling, or caused by the user

or other damage caused by not following the

operating instructions, or any fault acknow-

ledged at the time of purchase, is not covered

by the warranty. Damage caused by the use

of non-original accessories and consumable

material (e.g. sanding pads) is also excluded.

Complaints will only be acknowledged if the

equipment has not been dismantled before

being sent back to the suppliers or to an aut-

horised Festool customer support workshop.

Store the operating instructions, safety notes,

spare parts list and proof of purchase in a safe

place. In addition, the manufacturer‘s current

warranty conditions apply.

Note

We reserve the right to make changes to the

technical data contained in this infor-mation as

a result of ongoing research and development

work.

9 EU Declaration of Conformity

We declare under sole responsibility that this

product complies with the following norms or

normative documents:

EN 60745,EN 60335-2-29, EN 55014,

EN 61000 in accordance with the regulations

stipulated in Directive 2006/95/EC, 98/37/EC

(until 28 Dec. 2009), 2006/42/EC (from 29 Dec.

2009), 2004/108/EC.

Dr. Johannes Steimel

Head of research and development

Festool GmbH, Wendlingen, Germany

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Festool TDK 15 6 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Festool TDK 15 6 Manual

Product: