778619
16
Zoom out
Zoom in
Previous page
1/78
Next page
< 15%*
* Recommendation: Charge the battery pack
before any further use.
Further information about the charger and
battery pack with capacity indicator can be
found in the corresponding operating
manual.
8 Settings
CAUTION
Risk of injury
Only adjust the settings when the power
tool is switched off.
8.1 Changing direction of rotation [1-6]
Switch to the left = clockwise rotation
Switch to the right = counterclockwise rota
tion
8.2 Changing gear [1-8]
Only actuate the gear switch with the tool
switched off. Otherwise there is a risk of
damaging the gear unit.
Gear switch forwards (digit 1 visible) =
1st gear
Gear switch to rear (digit 2 visible) =
2nd gear
8.3 Fastening
Adjust the switch so that its marking [1-11]
faces the screw symbol [1-10].
Adjust the torque accordingly at the torque
wheel [1-12].
Position 1 = low torque
Position 25 = high torque
An acoustic signal sounds when the preset tor
que is reached and the machine then switches
off. You must release and press the ON/OFF
switch [1-5] again to start the machine.
8.4 Drilling
Adjust the switch [1-11] so that its marking
faces the drilling symbol [1-9]. Maximum tor
que is set in this position.
9 Tool holder, attachments
WARNING
Risk of injury
Remove the battery pack from the power
tool before performing any work on the
power tool.
CAUTION
Risk of injury from hot and sharp insertion
tool
Do not use any blunt or faulty insertion
tools.
Wear protective gloves when handling an
insertion tool.
9.1 CENTROTEC tool chuck [3]
Quick change of tools with CENTROTEC shaft
Only clamp CENTROTEC tools in CEN
TROTEC tool chucks.
9.2 Chuck [4]
For clamping drill bits and bits with max. shaft
diameter of 13 mm.
WARNING! Clamp the tool centrally in the
chuck.
9.3 Angle attachment [5]
Drilling and screwdriving at right angles to the
power tool (available as an accessory depend
ing on the model).
9.4 Eccentric adapter [6]
Screwdriving close to edges with bits according
to ISO 1173 (available as an accessory depend
ing on the model).
9.5 Tool holder in the drill spindle [7]
Bits can be inserted directly into the hexagon
socket holder of the drill spindle.
10 Working with the machine
WARNING
Risk of injury
Always secure the workpiece in such a
manner that it cannot move while being
machined.
10.1 Bit depot [1-4]
Magnetic, for storing bits and bit holders.
10.2 Acoustic warning signals
Acoustic warning signals sound and the ma
chine switches off in the following operating
states:
English
16
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool T18 plus 3 - 2021 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool T18 plus 3 - 2021 in the language / languages: All languages as an attachment in your email.

The manual is 2.15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Festool T18 plus 3 - 2021

Festool T18 plus 3 - 2021 Additional guide - All languages - 38 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info