497589
16
Zoom out
Zoom in
Previous page
1/97
Next page
16
T 12+3, T 15+3, T 18+3
GB
LED green - lit continuously
Battery pack is fully charged, or charging is
not started again, because the battery is
charged to more than 80 %.
LED red - flashing
General fault display, e.g. incomplete con-
tact, short circuit, battery pack faulty, etc.
LED red - lit continuously
Battery temperature is outside the permitted
range.
6.3 Charger wall mount
The charger TRC 3 has two elongated holes
on its back. It can be mounted on a wall us-
ing two screws (e.g. round head or flat head
screw with shank diameter of 5 mm) (see
Fig. [3]).
7 Settings
7.1 Changing direction of rotation
[1-4]
Switch to the left = clockwise rotation
Switch to the right = counterclockwise ro-
tation
7.2 Changing gear [1-6]
L
Only actuate the gear switch with the tool
switched off. Otherwise there is a risk of
damaging the gear unit.
Gear switch forwards (digit 1 visible) =
1st gear
Gear switch to rear (digit 2 visible) =
2nd gear
7.3 Fastening
Adjust the switch so that [1-9] its marking
faces the screw [1-8] symbol. The torque
can be adjusted in this position.
L
The switch-over function only works if the
machine is switched off.
X
Adjust the torque accordingly at the
torque [1-12] wheel:
Position 1 = low torque
Position 25 = high torque
The machine switches off when the preset
torque is reached and an acoustic signal
sounds. The machine only continues running
when the on/off switch is [1-3] released and
then pressed again.
7.4 Drilling
Adjust the switch [1-9] so that its marking
faces the drilling symbol [1-7]. Maximum
torque is set in this position.
8 Tool holder, attachments
8.1 Tool chuck CENTROTEC WH-CE
[4]
The tool chuck CENTROTEC WH-CE allows
you to change tools with a CENTROTEC
shank in a matter of seconds.
L
Always use a CENTROTEC tool chuck to
clamp CENTROTEC tools.
8.2 Chuck BF-FX [5]
The chuck BF-FX is used for clamping drill
and screwdriver bits.
8.3 Angle attachment DD-AS [6]
The angle attachment DD-AS (in part, addi-
tional equipment) permits drilling and screw-
driving at a right angle to the machine.
8.4 Eccentric attachment DD-ES [7]
The eccentric attachment (in part, additional
equipment) permits screwdriving near edges
with bits according to DIN 3126.
8.5 Tool holder in the drill spindle
[8]
Bits can be inserted directly in the hexagon
socket holder on the drill spindle to shorten
and reduce the weight of the machine.
9 Working with the machine
9.1 On/Off switch [1-3]
Press = ON, release = OFF
L
The speed of the machine depends on
how far the on/off switch is pressed in.
WARNING
Risk of injury, electric shock
X
Always disconnect the battery pack before
any type of work on the machine!
CAUTION
Tool has sharp edges and can cause cut-
ting injuries during a tool change.
X
Wear protective gloves!
CAUTION
Risk of injury
X
Clamp the tool centrally in the chuck!
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool T 15en3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool T 15en3 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info