Manual Festool SE-HL (page 8 of 38) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

498034

Zoom out

Zoom in

1/38

Symbols

Warning of general danger

Read the Operating Instructions/Notes!

1 Correct usage

The SE-HL device for bench mounting has been

designed to hold the Festool HL 850 EB planes so

that it can be operated upside down as station-

ary tool.

2 Preparatory work on the plane

Set the plane to a cutting depth of 0 mm and lock

with the locking lever.

If your plane has no marking (2.1) on the front you

will have to mark it yourself. The mark should be

made on the edge of the housing, roughly in the

middle as shown in Fig. 2.

3 Installation as operational device

3.1 Assembly of the device for bench mount-

ing

Lay the base plate (1.15) on a ﬂ at, ﬁ rm surface

(table top) with the anti-slip coating on the un-

derside.

Insert the two square nuts into the grooves (1.9

+ 1.12) to fasten the rear plane mounting (1.7) on

one end of the base plate.

The rear plane mounting is fastened ﬂ ush with the

end of the base plate using the Allen screws (1.8)

and tooth lock washers. The two remaining square

nuts are inserted into the front groove (1.12) at the

other end of the base plate and the front plane

mounting (1.16) ﬁ tted in the same manner.

These fastening screws should not yet be fully

tightened so that the mounting can be moved.

The starting clip (1.13) is fastened in the bore hole

(1.7) in the mounting by the enclosed chain.

3.2 Fitting the plane

Before fitting the plane in the device

for bench mounting unplug from the

mains.

The planes have a through bore at the rear of the

housing for installation in the device for bench

mounting.

Turn the plane upside down, insert into the rear

mounting (1.7) and push the bolts (1.11) through

the eyes (1.4 and 1.6) and bore hole in the hous-

ing before fastening with the rotary knob (1.10).

Move the front mounting (1.16) so that the locating

surfaces (1.2) ﬁ t in the guide groove of the rebate

depth stop on the plane housing. Lock the plane by

turning the rotary knob screw with a short thread

(1.14) through the eye (1.17) in the threaded bore

for the rebate depth stop. Now tighten the Allen

screw for the front mounting.

3.3 Adjusting the cutting depth to scale

Push the scale ring (2.2) onto the plane’s addi-

tional hand grip (2.3) with the mm scale pointing

inwards. Turn the scale ring until the zero position

is exactly in line with the marking on the plane

housing (2.1). If you release the plane’s cutting

depth lock you can now set the desired cutting

depth on the scale by turning the additional hand

grip.

4 Safety instructions

Please read before starting work!

4.1 Swivel hood

The swivel hood (1.3) automatically covers the

planer head when not in use.

Do always use the swivel hood!

4.2 Using a stop

The stop must always be used so that that part of

the planer head which is not in use is covered at

every planing width.

4.3 Using a feed device

A feed device should be used when planing small

workpieces.

4.4 Fastening the device for bench mount-

ing

Before starting work make sure that the device

for bench mounting is ﬁ xed securely to the base

(table), for example with clamps.

5 Starting

Push the switch clip with groove (1.13) onto the

guide plate (1.5) of the rear mounting and onto

the plane’s pistol switch until you feel a slight

resistance.

To switch the plane on, press the plane’s switch

lock and push the switch clip fully onto the han-

dle.

Remove the switch clip to turn the plane off.

6 Working with a stop

The plane can be used with the parallel stop PA-

HL, included with the plane, or the angle stop

WA-HL, available as an accessory.

Both are fastened in the same threaded bore

alongside the rear plate (see the operating in-

structions for the plane).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Festool SE-HL in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,23 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Festool SE-HL Manual

Product: