498035

Festool SE-EHL Manual

5
Zoom out
Zoom in
Previous page
1/30
Next page
5
Symbols
Warning of general danger
Read the Operating Instructions/Notes!
1 Correct usage
The SE-EHL device for bench mounting has been
designed to hold the Festool EHL 65 E and EHL 65
EB planes so that these can be operated upside
down as stationary tools.
2 Preparation of on the plane
The chip ejector connection must be mounted in
such a way that the extraction adapter is on the
left of the machine.
3 Installation as operational device
3.1 Assembly of the device for bench mount-
ing
Lay the base plate (1.4) on a fl at, fi rm surface
(table top) with the anti-slip coating (1.10) on the
underside.
Insert the two square nuts into the grooves (1.8
+ 1.9) to fasten the rear plane mounting (1.11) on
one end of the base plate.
The rear plane mounting is fastened fl ush with
the end of the base plate using the Allen screws
(1.13) and tooth lock washers.
The two remaining square nuts are inserted into
the front groove (1.8) at the other end of the base
plate and the front plane mounting (1.3) fi tted in
the same manner.
These fastening screws should not yet be fully
tightened so that the mounting can be moved.
The starting clip (1.6) is fastened in the bore hole
(1.14) by the chain (1.7).
3.2 Fitting the plane
Before fitting the plane in the device
for bench mounting unplug from the
mains.
The planes have a circular opening on the rear for
assembly purposes.
Turn the plane upside down and insert the peg
(1.12) on the rear mounting into this hole.
The plane is screwed to the side stop of the front
plane mounting through the bore hole (1.2) with
the screw (1.5).
The front plane mounting can now be screwed
tight onto the base plate.
3.3 Fitting the swivel hood
Place the torsion spring (2.3) on the arbour (2.4)
so that the end of the spring (2.6) enters the bore
hole (2.5) in the arbour.
Then place the swivel hood (2.8) onto the arbour
so that the other end of the spring enters the slot
(2.1) in the hub of the swivel hood.
Now turn the swivel hood in the direction of the
arrow (2.7) so that the lugs (2.2) on the arbour
and swivel hood engage and push the swivel hood
down onto arbour.
When fi tted properly, place the snap ring (3.1)
onto the free end of the arbour and push into the
annular groove (3.2).
The pre-assembled swivel hood is now mounted
on the front plane mounting (1.3) so that the lug
(3.3) fi ts into the corresponding square hole in the
mounting surface.
Finally, screw the swivel hood to the plane mount-
ing with the screw (1.1).
4 Safety instructions
Please read before starting work
4.1 Swivel hood
The swivel hood (1.15, assembly described in No.
3.3) automatically covers the planer head when
not in use.
Do always use the swivel hood!
4.2 Using the parallel stop
The parallel stop must always be used so that
that part of the planer head which is not in use is
covered at every planing width.
4.3 Using a feed device
A feed device should be used when planing small
workpieces.
4.4 Fastening the device for bench mount-
ing
Before starting work make sure that
the device for bench mounting is fi xed
securely to the base (table), for example
with clamps.
5 Starting
Suspend the clip (1.6) in the trigger switch and
push over the plane’s handle to switch on. This
holds the trigger switch in the ON position. Re-
move the clip to switch off.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool SE-EHL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool SE-EHL in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info