Manual Festool PSC400EB (page 21 of 132) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

573109

Zoom out

Zoom in

1/132

CARVEX

– If LiIon battery packs are to be stored for

long periods without use, they should be

charged to 40 % capacity (approx. 15 mins.

charging period).

10 Accessories

Use only original Festool accessories and Fes-

tool consumable material intended for this ma-

chine because these components are designed

specifically for the machine. Using accessories

and consumable material from other suppliers

will most likely affect the quality of your work-

ing results and limit any warranty claims. Ma-

chine wear or your own personal workload may

increase depending on the application. Protect

yourself and your machine, and preserve your

warranty claims by always using original Fes-

tool accessories and Festool consumable mate-

rial!

The order numbers of the accessories and tools

can be found in the Festool catalogue or on the

Internet under "www.festool.com".

10.1 Saw blades, other accessories

In order to saw different materials quickly and

cleanly, Festool offers saw blades for all appli-

cations that are specially designed for your Fes-

tool jigsaw.

10.2 Sawing with special base runners

The special base runners protect high-quality

surfaces against scratches and scores.

Press in the base runner at position [7-1].

At the same time, push the base runner for-

wards.

Mount another base runner and push it to

the rear until it engages.

10.3 Sawing with the angle table

The angle table WT-PS 400 is used for sawing in-

terior and exterior angles up to 45° and pipes.

Dust extraction is not possible when

sawing with the angle table!

Installing the angle table

Remove the saw table [1-10], (see chapter

7.4

Position the angle table against the saw ta-

ble support.

Close the change lever [1-8].

Ensure that the angle table is firmly seated in

the guide.

Setting the angle

Turn the adjusting wheel [8-1] to set the de-

sired angle.

You can set the values -45°, 0° and +45° using

the scale [8-2].

For 90° cuts, we recommend setting the an-

gle table to a small negative degree value to

guarantee stable running.

10.4 Sawing with the adaptation table

The adaptation table ADT-PS 400 is used for fit-

ting your jigsaw on the Festool guide rail and

the circle cutter KS-PS 400.

Installing the adaptation table

Remove the saw table [1-10], (see chapter

7.4

Mount the adaptation table [9-1] on the saw

table support.

Close the change lever [1-8].

Ensure that the adaptation table is firmly seat-

ed in the guide.

Use the extractor connector [1-7] also with

the adaptation table.

Adaptation to the guide rail FS 2

Using the Festool guide system FS 2 (Fig.

[10]) makes it easier to produce straight and

precise cuts, in particular, with material thick-

nesses up to 20 mm.

Place the jigsaw with attached adaptation

table [9-1] on the guide rail.

Adaptation to the circle cutter

The circle cutter can be used to create circular

cuts with a diameter between 120 and 3000

mm. The circle cutter can be installed from both

sides on the adaptation table.

Place the jigsaw with attached adaptation

table on the adapter [11-1] on the circle

cutter.

Insert the centring mandrel [11-2] in the

hole [11-4] on the circle cutter aligned with

the saw blade.

Clamp the measuring tape to the circle cut-

ter using the rotary knob [11-5].

Angle table position Application

Picture [8A] Angle, interior angle

Picture [8B]

Angle

Picture [8C]

Exterior angle, pipes

WARNING

Sawing cutting depths

Risk of injury

Select the saw blade length and cutting

depth so that the saw blade always stays

in the workpiece.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Festool PSC400EB in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,13 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Festool PSC400EB Manual

Product: