573109
18
Zoom out
Zoom in
Previous page
1/132
Next page
18
CARVEX
GB
The charger TRC 3 can be used to charge all
Festool battery packs of the BPS and BPC se-
ries. The charger automatically detects the type
of the inserted battery (NiCd, NiMH or LiIon). A
microprocessor controls the charging process in
line with the charging state, temperature and
voltage of the battery pack.
The LED [3-1] on the charger indicates the re-
spective operating status of the charger.
LED yellow - lit continuously
Charger is ready to use.
LED green - flashing quickly
Battery pack is charged to maximum capacity.
LED green - flashing slowly
Battery pack is charged with reduced current,
LiIon is charged to 80 %.
LED green - lit continuously
Battery pack is fully charged, or charging is not
started again, because the battery is charged
to more than 80 %.
LED red - flashing
General fault display, e.g. incomplete contact,
short circuit, battery pack faulty, etc.
LED red - lit continuously
Battery temperature is outside the permitted
range.
6.4 Charger wall mount
The charger TRC 3 has two elongated holes on
its back. It can be mounted on a wall using two
screws (e.g. round head or flat head screw with
shank diameter of 5 mm) (see Fig. [3]).
7 Settings
7.1 Changing tools
Selecting saw blade
Only use saw blades with a T-shank. The
saw blade should not be longer than that
required for the intended cut. To ensure
safe guidance, during the cut the saw blade
should emerge at the bottom of the workpiece
at every point.
L
Only use cross-set saw blades when using
the angle and adapter table. We recommend
Festool saw blade S 105/4 FSG.
Inserting saw blade
Always disconnect the battery pack from
the machine before every tool change!
X
If necessary, push the chip guard [4-1] up-
wards.
X
Push the saw blade [4-4] into the opening as
far as the stop with its teeth in cutting direc-
tion [4-2].
X
Turn the saw blade [4-4] approx. 30° clock-
wise until it engages.
The guidance jaws adjust automatically to the
saw blade used.
Check that the saw blade is secure. A
loose saw blade can fall out and cause an
injury.
L
In the case of very short saw blades, it is ad-
visable to remove the saw table (see chap-
ter
7.4
) before inserting the saw blade.
Ejecting saw blade
L
When ejecting the saw blade, hold the elec-
tric power tool such that no persons or ani-
mals can be injured.
X
Push the saw blade ejection [4-3] forwards
as far as the stop.
If the saw blade is not ejected:
run jigsaw 3
- 10 seconds at a high speed. Actuate saw
blade ejector mechanism [4-3] once again.
7.2 Using the chip guard
The chip guard [4-1] prevents chips flying away
and improves the efficiency of the chip extrac-
tion system.
X
Using minimal pressure, push the chip guard
[4-1] downwards.
7.3 Inserting splinterguard
The splinterguard makes cuts with splinter-free
cutting edges possible, even on the exit side of
the saw blade.
X
With the machine switched off, push the
splinterguard [5-1] onto the guide up to the
saw blade [5-2],
X
switch on the jigsaw,
WARNING
Risk of injury, electric shock
X
Always disconnect the battery pack before
any type of work on the machine!
CAUTION
Hot and sharp tools
Risk of injury
X
Wear protective gloves!
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool PSC400EB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool PSC400EB in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info