497994
18
Zoom out
Zoom in
Previous page
1/132
Next page
18
C A R V E X
GB
6.4 Charger wall mount
The charger
TRC 3
has two elongated holes on
its back. It can be mounted on a wall using two
screws (e.g. round head or flat head screw
with shank diameter of 5 mm) (see Fig.
[3]
).
7Settings
7.1 Changing tools
Selecting saw blade
Only use saw blades with a T-shank. The
saw blade should not be longer than
that required for the intended cut. To
ensure safe guidance, during the cut the saw
blade should emerge at the bottom of the
workpiece at every point.
L
Only use cross-set saw blades when using
the angle and adapter table. We recom-
mend Festool saw blade S 105/4 FSG.
Inserting saw blade
Always disconnect the battery pack
from the machine before every tool
change!
X
If necessary, lift up the chip guard
[4-1]
.
X
Slide the saw blade
[4-4]
into the open-
ing
[4-2]
as far as the stop with its teeth
in the cutting direction.
X
Turn the saw blade
[4-4]
clockwise ap-
prox. 30°.
Check that the saw blade is secure. A
loose saw blade can fall out and cause
an injury.
L
If the saw blade is very small, it is advis-
able to remove the saw base (see chapter
7.4) before inserting the saw blade.
Adjust the saw blade guide after every
saw blade change:
The saw blade guide was designed to improve
guidance of the saw blade.
X
Remove the saw base (see chapter
7.4
).
X
Tighten the screw
[4-6]
using the Allen
key
[4-5]
until the jaws are almost touch-
ing the saw blade.
Ejecting saw blade
L
When ejecting the saw blade, hold the elec-
tric power tool such that no persons or an-
imals can be injured.
X
Push the saw blade ejection
[4-3]
for-
wards as far as the stop.
L
A tool change is only possible when the tool
holder is located in the upper position!
If the saw blade is stuck and cannot be
changed:
Operate the jigsaw at high speed
for 3 - 10 seconds. Actuate the saw blade ejec-
tion
[4-3]
again.
7.2 Using the chip guard
The chip guard
[4-1]
prevents chips flying
away and improves the efficiency of the chip
extraction system.
LED yellow - lit continuously
Charger is ready to use.
LED green - flashing quickly
Battery pack is charged to maxi-
mum capacity.
LED green - flashing slowly
Battery pack is charged with
reduced current. Li-ion is
charged to 80 %.
LED green - lit continuously
Charging process has finished or
will not resume because the cur-
rent charging state is more than
80%.
LED red - flashing
General fault indicator, e.g.
incomplete contact, short circuit,
defective battery pack, etc.
LED red - lit continuously
Battery temperature is outside
the permitted range.
WARNING
Risk of injury, electric shock
X
Always disconnect the battery pack before
any type of work on the machine!
CAUTION
Hot and sharp tools
Risk of injury
X
Wear protective gloves!
NOTE
Damage to the machine or saw blade
X
Do not tighten the screw [4-6] too firmly!
It must be possible to move the saw blade
slightly.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool PSC CARVEX 420 EB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool PSC CARVEX 420 EB in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 12,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info