778632
21
Zoom out
Zoom in
Previous page
1/132
Next page
Keep the contacts on the power tool, charg
er and battery pack clean.
10.2 Cleaning the chip ejection opening
Clean the chip ejection opening [1-14] regularly
to prevent blockages:
Remove the chip guard.
Use a brush or vacuum cleaner to clean the
chip ejection opening.
Reinsert the chip guard.
11 Accessories
The order numbers of the accessories and tools
can be found in the Festool catalogue or on the
Internet at "www.festool.com".
11.1 Saw blades, other accessories
In order to saw different materials quickly and
cleanly, Festool offers saw blades for all appli
cations that are specially designed for your
Festool jigsaw.
11.2 Sawing with special base runners
The special base runners protect high-quality
surfaces against scratches and scores.
Press in the base runner at position [6-1].
At the same time, push the base runner for
wards.
Mount another base runner and push it to
the rear until it engages.
11.3 Sawing with the angle table
The WT-PS 400 angle table is used for
cutting pipes or interior and exterior an
gles up to 45°.
Dust extraction is not possible when sawing
with the angle table!
Installing the angle table
Remove the saw table [1-11] (see section
8.4).
Position the angle table against the saw
base support.
Close the lever [1-9].
Ensure that the angle table is firmly seated in
the guide.
Setting the angle
Turn the adjusting wheel [7-1] to select the
required angle.
You can select the angles -45°, 0° and +45° on
the scale [7-2].
WARNING
Sawing cutting depths
Risk of injury
Select the saw blade length and cutting
depth so that the saw blade remains
plunged in the workpiece.
For 0° cuts, we recommend setting the an
gle table to a small negative angle to guar
antee smooth operation.
11.4 Sawing with the base adapter
The ADT-PS 400 base adapter is used for at
taching your jigsaw to the Festool guide rail and
the KS-PS400 core maker.
With guide rail and core maker: Observe
the max. material thickness of 20 mm
and only use cross-set saw blades (FSG).
Installing the base adapter
Remove the saw table [1-11] (see section
8.4).
Position the base adapter [8-1] against the
saw table support.
Close the lever [1-9].
Ensure that the base adapter is firmly seated in
the guide.
Also use the extractor connector [1-8]
with the base adapter.
Adaptation to the FS 2 guide rail
The FS 2 Festool guide system (Fig. [9]) makes
it much easier to produce straight and precise
cuts.
Place the jigsaw with attached base adapter
[8-1] on the guide rail.
Adaptation to the core maker
The core maker can be used to create circular
cuts with a diameter between 120 and
3000 mm. The core maker can be installed from
both sides on the base adapter.
Place the jigsaw with attached base adapter
on the adapter [10-1] on the core maker.
Insert the centring mandrel [10-2] in the
hole [10-4] on the core maker aligned with
the saw blade.
Clamp the measuring tape to the core mak
er using the rotary knob [10-5].
Recommended settings when using the core
maker:
Cut in an anticlockwise direction.
Work at a slow rate of advance.
Set the pendulum stroke [1-12] to 0–1.
English
21
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool PSC 420 Li 18 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool PSC 420 Li 18 in the language / languages: All languages as an attachment in your email.

The manual is 3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info