573110
20
Zoom out
Zoom in
Previous page
1/132
Next page
20
CARVEX
GB
Freely guided sawing along a scribe mark
The triangular shape of the splinterguard [5-1]
points to the cutting line of the saw blade. This
facilitates sawing along a scribe mark.
8.1 Lighting
A continuous light or stroboscope is installed for
illuminating the cutting line:
up to approx. 2100 rpm: continuous light
from approx. 2100 rpm: stroboscope light
L
In overhead position (+/- 45°), the lighting
is switched off completely.
If required, you can adjust the lighting:
X
Press both buttons simultaneously [1-2] and
hold for approx. 10 s until a beep sounds.
X
Release both buttons [1-2].
X
Press the left button (on the pendulum
stroke side) to select the required mode:
X
Press the right button to save the setting.
8.2 Acoustic warning signal
Acoustic warning signals sound and the ma-
chine switches off in the following operating
states:
Battery flat or machine overloaded.
X
Change the battery.
X
Place the machine under reduced stress.
Machine is overheating.
X
You must allow the machine to cool before
using again.
LiIon battery pack is faulty or has overheated.
X
Once the battery pack has cooled, perform a
functional check using the charger.
9 Service and maintenance
Damaged safety devices and components must
be repaired or replaced in a recognised special-
ist workshop, unless otherwise indicated in the
operating manual.
Observe the following instructions:
Keep the air slits on the machine and the
charger free and clean to ensure adequate
cooling.
Keep the contacts on the machine, charger
and battery pack clean.
Check the guidance roller regularly for wear.
Regularly remove dust deposits from the chip
guard.
Regularly clean the base runner to prevent
scratches and cores on the surface.
Information on battery packs
Where possible, store the battery pack in a
cool, dry place at a temperature between
C and 25 °C.
Battery packs are most efficient at tempera-
tures between 20 °C and 30 °C.
– Protect the battery pack from moisture, wa-
ter and heat.
Significantly shorter operating times after
each charge indicate that the battery pack is
worn and should be replaced with a new one.
The LiIon battery pack is fully compatible
with the charger! Integrated electronics pre-
vent overloading and overheating during the
charging process.
Do not leave flat battery packs in a charger
disconnected from the mains power supply
for longer than one month. There is a risk of
total discharge and the maximum power of
the battery pack may decrease.
Store the battery pack in its packaging to re-
duce the risk of short circuits..
WARNING
The stroboscope light may make it diffi-
cult to determine the saw blade position
Risk of injury
X
Ensure the work area is well illuminated.
Mode Display during
configuration
Performance dur-
ing operation
1 Light flashes with stroboscope
(standard)
2Light on
Permanent light
without stroboscope
3 Light off Light switched off
peep ― ―
peep peep ―
peep peep peep
WARNING
Risk of injury, electric shock
X
Always disconnect the battery pack from the
machine before any maintenance or care work!
X
All maintenance and repair work which re-
quires the motor housing to be opened,
must only be carried out by an authorised
service workshop.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool PSBC400EB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool PSBC400EB in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info