497993

Festool PSB CARVEX 420 EBQ Manual

18
Zoom out
Zoom in
Previous page
1/107
Next page
18
C A R V E X
GB
To ensure constant air circulation, always keep
the cooling air openings in the motor housing
clean and free of blockages.
– Check the guidance roller regularly for wear.
– Regularly remove dust deposits from the
chip guard.
– Regularly clean the base runner to prevent
scratches and cores on the surface.
10 Accessories
The order numbers of the accessories and
tools can be found in the Festool catalogue or
on the Internet under "www.festool.com".
10.1 Saw blades, other accessories
In order to saw different materials quickly and
cleanly, Festool offers saw blades for all appli-
cations that are specially designed for your
Festool jigsaw.
10.2 Sawing with special base runners
The special base runners protect high-quality
surfaces against scratches and scores.
X
Press in the base runner at position
[6-1]
.
X
At the same time, push the base runner
forwards.
X
Mount another base runner and push it to
the rear until it engages.
10.3 Sawing with the angle table
The angle table WT-PS 400 is used for cutting
pipes or interior and exterior angles up to 45°.
Dust extraction is not possible when
sawing with the angle table!
Installing the angle table
X
Remove the saw base
[1-11]
, (see chap-
ter
7.4
).
X
Position the angle table against the saw
base support.
X
Close the lever
[1-9]
.
Ensure that the angle table is firmly seated in
the guide.
Setting the angle
X
Turn the adjusting wheel
[7-1]
to select
the required angle.
You can select the angles -45°, 0° and +45°
on the scale
[7-2]
.
L
For 90° cuts, we recommend setting the
angle table to a small negative angle to
guarantee smooth operation.
10.4 Sawing with the adaptation table
The adaptation table ADT-PS 400 is used for
attaching your jigsaw to the Festool guide rail,
the circle cutter KS-PS 400 and the CMS mod-
ular system.
With guide rail and circle cutter:
do
not exceed max. material thickness of
20 mm and always use cross-set saw
blades (FSG).
Installing the adaptation table
X
Remove the saw table
[1-11]
, (see chap-
ter
7.4
).
X
Mount the adaptation table
[8-1]
on the
saw table support.
X
Close the change lever
[1-9]
.
Ensure that the adaptation table is firmly seat-
ed in the guide.
L
Use the extractor connector
[1-8]
also
with the adaptation table.
Adaptation to the guide rail FS 2
The Festool guide system FS 2 (Fig.
[9]
)
makes it much easier to manufacture straight
precision cuts.
X
Place the jigsaw with attached adaptation
table
[8-1]
on the guide rail.
Adaptation to the circle cutter
The circle cutter can be used to create circular
cuts with a diameter between
120
and
3000
mm. The circle cutter can be installed from
both sides on the adaptation table.
X
Place the jigsaw with attached adaptation
table on the adapter
[10-1]
on the circle
cutter.
X
Insert the centring mandrel
[10-2]
in the
hole
[10-4]
on the circle cutter aligned
with the saw blade.
X
Clamp the measuring tape to the circle cut-
ter using the rotary knob
[10-5]
.
Recommended when using the circle cutter:
WARNING
Sawing cutting depths
Risk of injury
X
Select the saw blade length and cutting
depth so that the saw blade remains
plunged in the workpiece.
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool PSB CARVEX 420 EBQ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool PSB CARVEX 420 EBQ in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info