497993

Festool PSB CARVEX 420 EBQ Manual

15
Zoom out
Zoom in
Previous page
1/107
Next page
C A R V E X
15
GB
The specified emissions values (vibration,
noise)
– are used to compare machines.
– They are also used for making preliminary
estimates regarding vibration and noise
loads during operation.
– They represent the primary applications of
the power tool.
Increase possible for other applications, with
other insertion tools or if not maintained ade-
quately. Take note of idling and downtimes of
machine!
6Operation
Connecting and detaching the mains power
cable
[1-7]
see Fig.
[2]
.
X
Insert the plug into a socket.
The electric power tool has one button
[1-2]
on each side for switching on/off.
The
PSB 420 EBQ
also has a variable speed
trigger
[1-3]
with switch lock
[1-4]
. For con-
tinuous operation, use the button
[1-2]
.
7Settings
7.1 Changing tools
Selecting saw blade
Only use saw blades with a T-shank. The
saw blade should not be longer than
that required for the intended cut. To
ensure safe guidance, during the cut the saw
blade should emerge at the bottom of the
workpiece at every point.
L
Only use cross-set saw blades when using
the angle and adapter table. We recom-
mend Festool saw blade S 105/4 FSG.
Inserting saw blade
Always pull the mains plug out of the
socket before changing blades.
X
If necessary, lift up the chip guard
[3-1]
.
X
Slide the saw blade
[3-4]
into the opening
[3-2]
as far as the stop with its teeth in the
cutting direction.
X
Turn the saw blade
[3-4]
clockwise ap-
prox. 30°.
Check that the saw blade is secure. A
loose saw blade can fall out and cause an
injury.
L
If the saw blade is very small, it is advis-
able to remove the saw base (see chapter
7.4
) before inserting the saw blade.
Adjust the saw blade guide after every
saw blade change:
The saw blade guide was designed to improve
guidance of the saw blade.
X
Remove the saw base (see chapter
7.4
).
X
Tighten the screw
[3-6]
using the Allen
key
[3-5]
until the jaws are almost touch-
ing the saw blade.
Ejecting saw blade
L
When ejecting the saw blade, hold the elec-
tric power tool such that no persons or an-
imals can be injured.
X
Push the saw blade ejection
[3-3]
for-
wards as far as the stop.
L
A tool change is only possible when the tool
holder is located in the upper position!
WARNING
Unauthorised voltage or frequency!
Risk of accident
X
The mains voltage and the frequency of
the power source must correspond with
the specifications on the machine's name
plate.
X
In North America, only Festool machines
with the voltage specifications 120 V/60
Hz may be used.
WARNING
Risk of injury, electric shock
X
Always pull the plug out of the socket be-
fore performing any type of work on the
machine!
CAUTION
Hot and sharp tools
Risk of injury
X
Wear protective gloves!
NOTE
Damage to the machine or saw blade
X
Do not tighten the screw [3-6] too firmly!
It must be possible to move the saw blade
slightly.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool PSB CARVEX 420 EBQ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool PSB CARVEX 420 EBQ in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info