510170
15
Zoom out
Zoom in
Previous page
1/99
Next page
C A R V E X
15
GB
Increase possible for other applications, with other
insertion tools or if not maintained adequately. Take
note of idling and downtimes of machine!
6Operation
Connecting and detaching the mains power cable
[1-7]
see Fig.
[2]
.
Insert the plug into a socket.
The electric power tool has one button
[1-2]
on
each side for switching on/off.
The PSB 420 EBQ also has a variable speed trigger
[1-3]
with switch lock
[1-4]
. For continuous opera-
tion, use the button
[1-2]
.
7 Settings
7.1 Changing tools
Selecting saw blade
Only use saw blades with a T-shank. The
saw blade should not be longer than that re-
quired for the intended cut. To ensure safe
guidance, during the cut the saw blade should
emerge at the bottom of the workpiece at every
point.
Only use cross-set saw blades when using the
angle and adapter table. We recommend Fes-
tool saw blade S 105/4 FSG.
Inserting saw blade
Always pull the mains plug out of the socket
before changing blades.
If necessary, lift up the chip guard
[3-1]
.
Slide the saw blade
[3-4]
into the opening
[3-2]
as far as the stop with its teeth in the cutting di-
rection.
Turn the saw blade
[3-4]
clockwise approx. 30°.
Check that the saw blade is secure. A loose
saw blade can fall out and cause an injury.
If the saw blade is very small, it is advis-
able to remove the saw base (see chapter 7.4)
before inserting the saw blade.
Adjust the saw blade guide after every saw blade
change:
The saw blade guide was designed to improve guid-
ance of the saw blade.
Remove the saw base (see chapter 7.4).
Tighten the screw
[3-6]
using the Allen key
[3-
5]
until the jaws are
almost
touching the saw
blade.
Ejecting saw blade
When ejecting the saw blade, hold the electric
power tool such that no persons or animals can
be injured.
Push the saw blade ejection
[3-3]
forwards as
far as the stop.
A tool change is only possible when the tool
holder is located in the upper position!
If the saw blade is stuck and cannot be changed:
Operate the jigsaw at high speed for 3 - 10 seconds.
Actuate the saw blade ejection
[3-3]
again.
7.2 Using the chip guard
The chip guard
[3-1]
prevents chips flying away and
improves the efficiency of the chip extraction sys-
tem.
Using minimal pressure, push the chip guard
[3-1]
downwards.
7.3 Inserting the splinterguard
The splinterguard prevents the edges of the mate-
rial from splintering during the cut, even at the end
where the saw blade exits the material.
Switch off the machine and slide the splinter-
guard
[4-1]
into the guide
[4-2]
and up to the
WARNING
Unauthorised voltage or frequency!
Risk of accident
The mains voltage and the frequency of the pow-
er source must correspond with the specifica-
tions on the machine's name plate.
In North America, only Festool machines with
the voltage specifications 120 V/60 Hz may be
used.
WARNING
Risk of injury, electric shock
Always pull the mains plug out of the socket be-
fore performing any type of work on the ma-
chine!
CAUTION
Hot and sharp tools
Risk of injury
Wear protective gloves.
NOTE
Damage to the machine or saw blade
Do not tighten the screw [3-6] too firmly! It must
be possible to move the saw blade slightly.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool PSB 420 EBQ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool PSB 420 EBQ in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info