573107

Festool PS400EBQ Manual

19
Zoom out
Zoom in
Previous page
1/110
Next page
CARVEX
19
GB
cessories and consumable material from other
suppliers will most likely affect the quality of
your working results and limit any warranty
claims. Machine wear or your own personal
workload may increase depending on the ap-
plication. Protect yourself and your machine,
and preserve your warranty claims by always
using original Festool accessories and Festool
consumable material!
The order numbers of the accessories and
tools can be found in the Festool catalogue or
on the Internet under "www.festool.com".
10.1 Saw blades, other accessories
In order to saw different materials quickly and
cleanly, Festool offers saw blades for all appli-
cations that are specially designed for your
Festool jigsaw.
10.2 Sawing with special base runners
The special base runners protect high-quality
surfaces against scratches and scores.
X
Press in the base runner at position [6-1].
X
At the same time, push the base runner
forwards.
X
Mount another base runner and push it to
the rear until it engages.
10.3 Sawing with the angle table
The angle table WT-PS 400 is used for sawing
interior and exterior angles up to 45° and
pipes.
Dust extraction is not possible when
sawing with the angle table!
Installing the angle table
X
Remove the saw table [1-11], (see chapter
7.4
).
X
Position the angle table against the saw ta-
ble support.
X
Close the change lever [1-9].
Ensure that the angle table is firmly seated in
the guide.
Setting the angle
X
Turn the adjusting wheel [7-1] to set the
desired angle.
You can set the values -45°, 0° and +45° us-
ing the scale [7-2].
L
For 90° cuts, we recommend setting the
angle table to a small negative degree val-
ue to guarantee stable running.
10.4 Sawing with the adaptation table
The adaptation table ADT-PS 400 is used for
attaching your jigsaw to the Festool guide rail,
the circle cutter KS-PS 400 and the CMS mod-
ular system.
Installing the adaptation table
X
Remove the saw table [1-11], (see chapter
7.4
).
X
Mount the adaptation table [8-1] on the
saw table support.
X
Close the change lever [1-9].
Ensure that the adaptation table is firmly seat-
ed in the guide.
L
Use the extractor connector [1-8] also with
the adaptation table.
Adaptation to the guide rail FS 2
Using the Festool guide system FS 2 (Fig.
[9]) makes it easier to produce straight and
precise cuts, in particular, with material thick-
nesses up to 20 mm.
X
Place the jigsaw with attached adaptation
table [8-1] on the guide rail.
Adaptation to the circle cutter
The circle cutter can be used to create circular
cuts with a diameter between 120 and 3000
mm. The circle cutter can be installed from
both sides on the adaptation table.
X
Place the jigsaw with attached adaptation
table on the adapter [10-1] on the circle
cutter.
X
Insert the centring mandrel [10-2] in the
hole [10-4] on the circle cutter aligned with
the saw blade.
X
Clamp the measuring tape to the circle cut-
ter using the rotary knob [10-5].
Recommended when using the circle cutter:
X
Cut in an anticlockwise direction.
X
Work at a slow rate of advance.
Angle table
position
Application
Picture [7A] Angle, interior angle
Picture [7B] Angle
Picture [7C] Exterior angle, pipes
WARNING
Sawing cutting depths
Risk of injury
X
Select the saw blade length and cutting
depth so that the saw blade always stays
in the workpiece.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool PS400EBQ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool PS400EBQ in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info