382959
14
Zoom out
Zoom in
Previous page
1/86
Next page
14
TRION
GB
count any machine idling times and down-
times to estimate these values more accu-
rately for a specified time period. This may
significantly reduce the load during the ma-
chine operating period.
6 Operation
Connecting and detaching the mains power
cable [1-3] see Fig. [2a].
PS 300 Q, PS 300 EQ
The power tool has a slide switch to switch
the tool on and off (I = ON, 0 = OFF).
PSB 300 Q, PSB 300 EQ
The power tool have a push button switch [2-
2] to switch the tool on and off.
The locking button [2-1] can be engaged to
operate in continuous mode. Press the switch
again to release the knob.
7 Settings
7.1 Changing tools
X
Open chuck lever [3-4] up to the stop,
X
remove fitted saw blade,
X
insert new saw blade up to the stop in the
saw blade holder [3-1],
X
close chuck lever.
7.2 Adjusting three saw blade guide
The pendulum jigsaws have an additional
hard metal guide [3-2] immediately above
the workpiece for a better guidance of the
saw blade.
X
Tighten the screw [3-3] with the Allen
keyl [1-4] until the jaws almost rest
against the saw blade.
The saw blade should still be able to be
moved easily!
7.3 Fitting the splinterguard
The splinterguard allows cuts with splinter-
free edges, even on the exit side of the saw
blade.
X
With the tool switched off, fit the splinter-
guard [4-3] on the guide [4-2] up to the
saw blade,
X
switch the jigsaw on,
X
with the tool running, push the splinter-
guard in until the splinterguard is flush
with the front edge of the base runner.
Thereby the splinterguard is cut in.
L
The splinterguard must lie close to the
saw blade on both sides to ensure its reli-
able operation. Thus, a new splinterguard
should be fitted every time the saw blade
is changed to ensure splinter-free cuts.
7.4 Fitting the chip guard
The chip guard prevents chips from flying off
and improves the efficiency of the chip ex-
tractor.
X
Insert the chip guard [2-8] between the
base runner and chuck lever,
X
push back the chip guard with a slight
pressure until it catches in place.
7.5 Dust extraction
Jigsaws can be connected to a dust extractor
(hose diameter 27 mm) using the extractor
adapter [2-4].
WARNING
Unauthorised voltage or frequency!
Risk of accident
X
The mains voltage and the frequency of
the power source must correspond with
the specifications on the machine's name
plate.
X
In North America, only Festool machines
with the voltage specifications 120 V/60
Hz may be used.
WARNING
Risk of injury, electric shock
X
Always pull the plug out of the socket be-
fore performing any type of work on the
machine!
WARNING
Risk of injury, electric shock
X
Always pull the plug out of the socket be-
fore performing any type of work on the
machine!
WARNING
Dust hazard
X
Dust can be hazardous to health. Always
work with a dust extractor.
X
Always read applicable national regula-
tions before extracting hazardous dust.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool ps 300 eq plus al at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool ps 300 eq plus al in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian as an attachment in your email.

The manual is 1,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info