Manual Festool PRECISIO CS 70 EG - 2020 (page 28 of 196) (All languages)

778612

Zoom out

Zoom in

1/196

8b Table saw with sliding function (ﬁg. 3)

fRelease the saw lock by turning the rotary

knob [2-6] anticlockwise.

It can now be used to move the saw unit backwards

and forwards for making cuts. The backwards mo-

tion is supported by a spring force.

8.1 Extra feet [1-3]

Always use the extra feet with an extension table

(width or length) or sliding table.

fLoosen the screw [1-4], swivel the leg

[1-3] down until it has settled on the ﬂoor and

retighten the screw [1-4].

8.2 Fitting the accessory holder

See ﬁgures 13 and 14.

fWhen connecting the two individual parts,

make sure that the tabs on the latches ﬁt

together exactly and lock in place.

fAlso check the back of the accessory holder to

make sure the latches are in the correct posi-

tion in the holding brackets.

8.3 Cuts along the mitre

For cuts along the mitre, the preset proﬁle set-

ting rail should be on the right-hand side of the

table.

8.4 Switching on the machine when cutting

metal

When cutting metal, switch on the saw using a

residual current circuit breaker.

8.5 Set-up position

Always move the saw into the set-up position be-

fore conﬁguring any settings on the machine:

The saw is locked in the off position upon deliv-

ery.

fTurn the rotary knob [2-6] anticlockwise to

release the lock and pull the saw forwards.

fPush the notch lever [1-9].

The saw is now locked in the middle position.

8.6 Setting the cutting height

To set the cutting height in set-up position any-

where between 0-70 mm:

fTurn the cutting height adjuster [1-10].

LTo ensure a precise saw cut, set the cutting

height 2-5 mm greater than the thickness of

the workpiece.

8.7 Setting the mitre angle

The saw blade can be swivelled between 0° and

45° in set-up position:

fUnscrew the rotary knob [2-4].

fSet the mitre angle using the rotary handle

[2-3] with reference to the scale [2-5].

fTighten the rotary knob [2-4].

For precision trimming work (undercuts on abut-

ting edges), the saw blade can be swivelled out

2° beyond the two end positions.

fTo do this, press and hold the button [2-2] in

the end position.

The saw blade can now be swivelled to -2° or 47°

using the rotary handle [2-3]. Releasing the but-

ton [2-2] reactivates the 0° and 45° stops.

8.8 Changing tools

WARNING

Risk of accident, electric shock

fAlways disconnect the mains plug from the

socket before performing any work on the

machine.

CAUTION

Hot and sharp tools

Risk of injury

fWear protective gloves.

Removing the saw blade

fWear gloves when changing the tool, but not

when cutting.

fLock the saw in set-up position.

fSet the greatest inclination and the maximum

cutting height.

fLoosen the clamp on the insert using the rota-

ry knob [5-1].

fSlide the clamping plate forwards.

fReach underneath the table insert [1-7] to lift

the back and remove it towards the back of the

table.

fRemove the guard, see section 6.2b.

fTake the hex key [5-3] out of the holder on the

saw blade cover [5-10].

fRelease the locks [5-9] using the rotary knob

and the hex key [5-3] and swivel the saw blade

cover [5-10] downwards.

fInsert the hex key [5-3] into the saw blade

retaining screw.

fPress and hold the spindle stop [5-2] (behind

the saw blade) and use the hex key to turn the

saw shaft until the spindle stop [5-2] engages

and the saw shaft locks.

P R E C I S I O - GB

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Festool PRECISIO CS 70 EG - 2020 in the language / languages: All languages as an attachment in your email.

The manual is 3.42 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Festool PRECISIO CS 70 EG - 2020 Manual

Product: