778610
29
Zoom out
Zoom in
Previous page
1/180
Next page
29
- Move the riving knife [7-1] into the lower locking
position by pushing it down firmly.
Creating non-through cuts
When executing non-through cuts, pay particular
attention that the tool is guided precisely. To do
this, push the workpiece down firmly onto the
table. Select the cutting sequence so that the
workpiece side already sawed out is not the fence
side (risk of kickback).
Rabbeting
- Set the cutting depth and fence of the first side
of the rebate.
- Carry out the first saw cut of the rebate by guid-
ing the workpiece by hand. Keep your arms away
from the saw blade’s centre line.
- Use the push stick [2-4] to guide the workpiece
past the saw blade.
- Turn the workpiece.
- Set the cutting depth and fence of the second
side of the rebate.
- Make the second saw cut of the rebate.
- Use the push stick [2-4] to guide the workpiece
past the saw blade.
Rabbeting on workpieces ≤ 12 mm with a table
saw with sliding function (with the saw blade
locked)
- Use the fence as a cross-cutting fence (fig. 3).
- Observe the operating instruction for cross cuts
(see section 8.2a).
NEVER use the fence as a rip fence when
rabbeting on the short side.
Grooving
- Adjust the cutting depth on the saw blade.
- Use the fence as a guide.
- Guide the workpiece by hand. Keep your arms
away from the saw blade‘s centre line.
- Use the push stick [2-4] to guide the workpiece
past the saw blade.
- Repeat the process until the required grooving
depth is achieved.
After finishing work
- After executing the non-through cuts, move the
riving knife [7-1] back into the upper position
and attach the guard [6-4a].
Complicated concealed cut process
- e.g. plunge saws, resawing, dadoing, profile
routing and fluting are not permitted.
8.1d Featherboard
NOTE
Use a featherboard for non-through cuts. Fit the
featherboard on the fence and the table so that the
featherboard pushes the workpiece down firmly
onto the plate during cutting. Featherboards are
not included with the delivery.
8.1e Longitudinal cuts at an angle
- Only use the left fence when making longitudinal
cuts at an angle in material with an edge length
of ≤ 150 mm. This creates more space between
the fence and the saw blade.
8.2 Using the machine as a table saw with
sliding function
8.2a Cross cuts
- Place the saw blade in the back table position,
see section 5.4 b).
- Use the preset profile setting rail as a crosswise
or angle ruler (fig. 3) to position the workpiece
and hold it in place. Fastening clamps (not
included in delivery) can be inserted into the
grooves [3-8] to secure the workpiece. Carry
out the saw cut by swivelling the handle [3-9]
downwards and using it to pull the saw unit
forwards.
- After completing the cut, move the saw unit right
back to its starting position before removing the
workpiece from the preset profile setting rail.
8.2b Angled cuts
- The mitre angle of the saw blade needs to be
adjusted for angled cuts, see section 7.2. The
preset profile setting rail is on the right-hand
side of the table.
- For mitre cuts, the preset profile setting rail has
to be adjusted, see section 7.5.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool PRECISIO CS 50 EG - 2021 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool PRECISIO CS 50 EG - 2021 in the language / languages: All languages as an attachment in your email.

The manual is 7.36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info