Manual Festool MFT3 (page 8 of 48) (All languages)

778799

Zoom out

Zoom in

1/48

1 Technical data

MFT/3

Bench dimensions (width x

length) 1157 x 773 mm

(45.6“ x 30.4“)

Bench

height

- with foldaway

legs 900 mm (35.4“)

- without foldaway

legs 180 mm (7.1“)

max. working width 700 mm (27.6“)

max. workpiece thickness 78 mm (3.1“)

Weight 28 kg (61.7 lb)

2 Symbols

Warning of general danger

Read the Operating Instructions/Notes!

The speciﬁ ed illustrations are at the beginning of

the Operating Instructions.

3 Scope of delivery

[1-1] Bench consisting of: proﬁ le frame, cor-

ner feet, perforated top, foldaway legs

[1-2] Support unit

[1-3] Guide rail FS 1080

[1-4] Swivel unit

[1-5] Pre-set proﬁ le setting rail and

[1-6] Stop ruler

[1-7] Additional clamp for stop ruler

[1-8] Stop ﬂ ag MFT/3-AR

[1-9] Deﬂ ector

4 Intended use

The multifunction table MFT/3 is designed for

safe, accurate sawing and routing in combina-

tion with Festool electric power tools.

The clamping systems included in the acces-

sories programme enable the user to attach

workpieces securely to the worktop. The base

becomes a work bench for various tasks such as

planing, sanding, carving, etc.

The user bears the responsibility for damage

and accidents caused by improper use.

5 Setting up and attaching

Accessory attachments can be secured at differ-

ent points on the multifunction table to enable

different working positions.

In the standard working position, the user stands

along one side of the bench [Fig. 2]. In these op-

erating instructions, this side of the bench is re-

ferred to as the "front".

5.1 Setting up

Screw on the knobs [2-3] until the stop is

reached. Unfold the foldaway legs and tighten

the knobs on the joints to secure. Turn the end

cap [2-1] on the right to adjust the length of the

leg and compensate for an uneven ﬂ oor surface.

The corner feet [2-4] are ﬁ tted with rubber caps

so that the bench stands securely when the legs

are folded away.

5.2 Attaching the guide rail

Stops [3-1/4-4] are attached to the longitudi-

nal proﬁ le on the front and back of the bench ex

works for the recommended working position.

The swivel unit [1-4/3-2] is secured to the longi-

tudinal back edge and the support unit [1-2/2-2]

to the longitudinal front edge.

Unscrew the height adjustment clamp [4-3] and

the rotary knob [4-1], slide the units along the

proﬁ led groove from the left up to the stop and

then tighten the rotary knob [4-1] again to se-

cure. To eliminate play, you can adjust both units

in the proﬁ led groove by turning the adjusting

screws [4-2] in the guide spring using a size 2.5

Allen key.

To make both units more accessible, lift the metal

plates all the way up and push down the clamp-

ing lever [4-3] to secure in position. If required,

you can adjust the screws [4-2] to increase the

clamping effect.

To attach the guide rail, place on the key [3-3]

and make sure that the end of the rail is resting

on the support plate and the key is located cor-

rectly in the groove.

Secure the guide rail in this position with the

two screws [3-4] and tighten using the hexagon

wrench.

5.3 Deﬂ ector

The deﬂ ector [1-9] prevents the extraction hose

and the power cable from catching on the guide

rail. The deﬂ ector is attached to the end of the

guide rail and secured with the rotary knob [1-

10].

Multifunction table

MFT/3

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Festool MFT3 in the language / languages: All languages as an attachment in your email.

The manual is 1.39 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Festool MFT3 Manual

Product: