778809
23
Zoom out
Zoom in
Previous page
1/172
Next page
7 Settings
WARNING
Risk of injury, electric shock
Always disconnect the mains plug from the
socket before performing any work on the
machine.
7.1 Motor and electronics
The power tool is equipped with a brushless
EC-TEC motor for a long service life and power
electronics with the following properties:
Smooth start-up
The electronically controlled smooth start-up
function ensures that the power tool starts up
smoothly.
Speed control
You can use the adjusting wheel [1-9] to contin
uously adjust the speed within the speed range
(see section 4). This enables the sanding speed
to be optimally adjusted to suit the material you
are working on.
Constant speed
The preselected motor speed is kept constant
through electronic control. This means that, if
the machine is used as intended (reasonable
contact pressure), a constant sanding speed is
achieved.
Overheating protection
To avoid the power tool overheating, the power
consumption is limited at an excessive temper
ature (e.g. if the pressure is too high while
working). If the temperature continues to rise,
the power tool switches off. It can only be
switched on again once the power tool has
cooled sufficiently.
Overload protection
The power tool will switch off if the backing pad
becomes jammed or if the motor becomes
overloaded, see also Section 13.
7.2 Changing the abrasives [6]
CAUTION
Deteriorated suction power and increased
dust exposure
Heath hazard posed by dust
The hole pattern in the abrasive must be
aligned with the holes in the interface pad.
Only use recommended abrasives with the
appropriate hole pattern.
Compatible StickFix abrasives are quick and
easy to attach to the interface pad.
Press the abrasive [6-1] onto the interface
pad [6-2].
7.3 Changing the interface pad [7]
CAUTION
Decreasing StickFix coating adhesion
Risk of injury from flying parts
Check the StickFix coating on the interface
pad and the abrasive regularly for wear.
Replace interface pad/abrasive with worn
StickFix coating.
The interface pad is attached to the backing pad
with eight screws.
Remove the abrasive.
Loosen screws by turning the screwhead
or a coin (e.g. a euro) anticlockwise.
Remove the interface pad [7-1].
Vacuum the backing pad and clean with
a brush if necessary.
Place a new interface pad on the backing
pad.
Insert all eight screws one after the oth
er.
The interface pad is optimally aligned.
Tighten all screws clockwise in a
crosswise sequence.
7.4 Replacing the backing pad [8]
CAUTION
Worn backing pad, backing pad revs up
Risk of injury from flying parts
Check backing pad regularly for wear.
Change backing pads if necessary.
The backing pad is attached to the power tool
with eight screws.
To remove the abrasive and interface pad,
see Sections 7.2 and 7.3.
Loosen the screws by turning a suitable
screwdriver anticlockwise.
Remove the backing pad [8-1] carefully
by gently pulling it. Take care to ensure that
no dirt enters the eccentric housing.
Extract dirt particles if necessary.
Place new backing pad so that the open
ings in the backing pad match with the
screw threads.
Insert all eight screws one after the oth
er.
English
23
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool LHS 2 225 EQI PLANEX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool LHS 2 225 EQI PLANEX in the language / languages: All languages as an attachment in your email.

The manual is 3.79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info