778810
22
Zoom out
Zoom in
Previous page
1/172
Next page
[1-8] Handle
[1-9] Speed control
[1-10] Plug-it connection
[1-11] Extractor connector
[1-12] Suction sleeve stop
[1-13] Locking lever
[1-14] Extension tube
[1-15] Suction regulator
[1-16] Sanding head
[1-17] Surface control light
[1-18] Backing pad
[1-19] Interface pad
[1-20] Plug-it mains power cable
[1-21] Insulated gripping surfaces
The illustrations specified are located at the be
ginning and end of the operating instructions.
6 Commissioning
WARNING
Risk of injury, electric shock
Always disconnect the mains plug from the
socket before performing any work on the
machine.
6.1 Assembling/disassembling
WARNING
Incorrect installation
Risk of injury from falling parts and loss of
control
Before switching on the power tool, make
sure that all locking levers are completely
closed.
Assembly [2]
The long-reach sander consists of a
LHS 2 225 EQI or LHS 2 225 EQ handle [1-1], a
maximum of two extension tubes VL-
LHS 2 225 [1-14] and a sanding head HE-
LHS 2 225 [1-16].
Push the pipe end of the sanding head
into the opening on the handle as far as it
will go.
Turn the locking lever [2-1] towards the
sanding head as far as it will go.
Check whether the handle and sanding
head are firmly connected by pulling them
apart.
The handle and sanding head are securely con
nected.
Assemble the extension tubes in the same way
as the handle.
Disassembling [3]
Open the locking lever [3-1].
Turn the locking lever [3-1] further to
wards the end of the handle as far as it will
go and hold it in this position. Pull the sand
ing head and handle apart at the same time.
The sanding head and handle are separate and
can be stored in a Systainer.
Disassemble the extension tubes in the same
way as the handle.
6.2 Connecting
WARNING
Unauthorised voltage or frequency.
Risk of accidents
The mains voltage and the frequency of the
power source must correspond to the
specifications on the name plate.
In North America, only Festool machines
with the voltage specifications 120 V/60 Hz
may be used.
CAUTION
Heating of the Plug it connection if bayonet
fitting is not completely locked
Risk of burns
Before switching on the power tool, make
sure that the bayonet fitting at the mains
cable is closed fully and locked.
Connect and disconnect the mains power
cable - [4].
To connect the suction hose [5], see also
Section 7.6.
Using a special vacuum sleeve, the PLANEX
suction hose guarantees a permanent fixing
and better protection against kinking.
6.3 Switching on/off
On/off switch [1-5]
I = ON, 0 = OFF
English
22
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool LHS 2 225 EQ PLANEX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool LHS 2 225 EQ PLANEX in the language / languages: All languages as an attachment in your email.

The manual is 3.79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info