778622
9
Zoom out
Zoom in
Previous page
1/64
Next page
1 Symbols
Warning of general danger
Read the operating instructions and
safety instructions.
Do not dispose of it with domestic
waste.
Disconnecting the mains power cable
Tip or advice
Handling instruction
2 Safety warnings
WARNING! Read all safety warnings,
instructions, illustrations and specifica
tions provided with this power tool. Failure to
follow all instructions listed below may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term "power tool" in the warnings refers to
your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
Observe the operating manual of the power
tool.
3 Intended use
The AH-ES-ETS/ETSC is intended for sanding
edges in connection with the ETS 125 REQ,
ETSC 125 Li power tools.
The AH-ES-ETS/ETSC must not be used in
conjunction with the ETS 125 EQ power tools or
any orbital sanders/delta sanders (DTS 400,
RTS 400, DTSC 400, RTSC 400).
Do not use the AH-ES-ETS/ETSC with the
ST-STF 125/8-M4-J SW sanding pad. The
larger size of the sanding pad can cause
the abrasive to collide with the base
runner.
4 Parts of the device
[1-1] Sanding mode setting
[1-2] Handle
[1-3] Angle lock rotary knob
[1-4] Angle display
[1-5] Base runner button
[1-6] Base runner
The specified illustrations appear at the begin
ning of the Operating Instructions.
5 Assembly
5.1 AH-ES-ETS/ETSC Assembling on the
power tool [2]
Insert the housing shell [2-2] into the
protector groove [2-3] of the power tool.
Place the counterpart housing shell [2-1]
on top.
Connect the housing shells with the two
enclosed screws and a hex key.
5.2 Calibrating the angle display [3]
The machine has an adjustable angle display.
After first assembling it on your power tool, the
angle display must be calibrated to your power
tool.
Set the sanding mode to "Hard" (see
Section 6.1 ).
Release the angle lock rotary knob [3-3].
Use a measuring tool to set the angle to
90°.
Tighten the angle lock rotary knob.
Loosen the angle calibration locking
screw [3-1].
Move the angle display [3-2] until the
display points to the 90° mark.
Tighten the angle calibration locking screw.
6 Settings
WARNING
Risk of injury, electric shock
Always disconnect the mains plug from the
socket before performing any work on the
machine.
6.1 Sanding mode setting
Hard mode [4a]
In Hard mode (setting for pre-sanding), the
edge is sanded according to the set angle.
Soft mode [4b]
In Soft mode (setting for intermediate sanding),
the AH-ES-ETS/ETSC adapts exactly to the
existing surface so that paint or filler is not
sanded through.
6.2 Setting the sanding angle
See figure [5].
English
9
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool ES-ETS 125 - 2021 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool ES-ETS 125 - 2021 in the language / languages: All languages as an attachment in your email.

The manual is 2.35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info