574919
17
Zoom out
Zoom in
Previous page
1/99
Next page
17
Removing the auto feed attachment
Use power to carefully pull the attachment
from the gear box.
Setting the screw length
Press button [9-1] to remove and insert the
depth stopper [9-2] and set the required screw
length.
Read the set screw length on the stopper sides
[9-3].
Inserting collated screw strips
Pull the collated screws [10-3] through the
bottom guiding of the attachment, then push
the strip through the second guiding until it
engages in the working position.
Pull the belt slightly to make sure that it is
safely fi tted.
Make sure that the fi rst screw is in the screw-
ing axes – see fi gure [10].
Use the wheel [10-1] to set the required screw-
ing depth. Turn to the right for inserting the
screws deeper, and to the left to screw to lower
depth. The actual setting position is visible on
the presetting indicator [10-2].
Upon setting, set some screws for testing and use
the wheel [10-1] to adjust the depth, if required.
Each setting change complies with the stopper
shift o ± 0.1 mm.
We recommend to screw in automatic mode –
see point 9.1 b).
Removing the collated screws
Pull upwards to remove the belt (fi gure [11]
) or press the transport lever and concurrently
pull the belt downwards (fi gure [11] ).
10 Working instructions
- The auto feed attachment must not be held in
the depth stopper area as there are moving
parts!
- Each screw adjustment must be completed. In-
terrupted fastening or releasing of the pressure
during adjustment can result in unsatisfactory
machine function.
- The collated screws and the auto feed attach-
ment can only be replaced when the power tool
is turned off.
- Never use the auto feed attachment in any other
way than specifi ed in this instruction manual.
- Use only original screwing bits.
- Use only original collated screws.
- Always store the collated screws in original
packaging.
- Always work in right angle against the attached
board.
Maintenance of the auto feed attachment
The attachment generally does not require any
maintenance. After long period use, we recom-
mend to clean with pressurized air.
The auto feed attachment may be lubricated in
the area of the carriage guide (see picture [12 b]).
Prior to cleaning, dismantle the attachment, as
specifi ed above.
Prior to cleaning, remove the collated screws
from the attachment, as specifi ed in the point
Removing the collated screws.
Pull the auto feed attachment from the drywall
screwdriver.
Disassembly of the slides
1. Push the depth stopper [9-2] into the housing
until the arresting button [12-1] is at the level
of the sign for dismantling the slides [12-2]
see fi gure [12 a].
2. Press the arresting button [12-1] and concur-
rently remove the slides from the holder – see
gure [12 b].
3. Press the button [9-1] and concurrently re-
lease the depth stopper – see fi gure [12 c].
Transport lever disassembly
1. Press the button [13-1] and concurrently pull
it out– see fi gure [13 a].
2. Remove the released button [13-1] (figure
[13 b]) with the transport lever [13-2] and the
spring [13-3] from the slides (fi gure [13 c]).
Clean individual parts, replace defective or worn
parts, and assemble in the opposite sequence.
CAUTION
During reassembly of the transport lever into
the slides, pay due care to correct fi tting of the
spring [13-3] in the transport lever. Incorrect
assembly may result in dysfunction of the belt
transport.
Acoustic warning signal
Acoustic warning signals sound and the machine
switches off in the following operating states:
peep
- Battery at or machine
overloaded
Change the battery pack.
Place the machine under
reduced stress.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool DWC 18-2500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool DWC 18-2500 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 11,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info