Manual Festool DF 700 EQ - Dominio XL - 2021 (page 15 of 103) (All languages)

778804

Zoom out

Zoom in

1/103

DF 700 EQ



Set the desired routing height

using the scale

[5-3]

by moving the front section of the guide

frame vertically.



Close the clamp lever

[5-1]

7.5 Setting the Fence Angle



Loosen the clamp lever for the angle adjust-

ment

[5-4]



Set the desired angle:



using the scale

[5-5]

variable from 0° to 90°.



locking at 0°; 22.5°; 45°; 67.5°; 90°.



Close the clamp lever

[5-4]

Set the routing height and depth as low as

possible when mitre routing as otherwise

there is a risk that the cutter will come out

the other side.

7.6 Setting the Mortise Width

Use the adjusting lever

[1-6]

to adjust the width of

the dowel hole you intend to cut for an adequate fit

or set with 3 mm play:

You can see on the display

[1-5]

what dowel hole

width is selected.

7.7 Setting stop pins

Six stop pins

[1-2]

are available on the stop side of

the DOMINO joining machine.

Stop pins that are not required can be individually

engaged by exerting overpressure and released us-

ing the button

[1-13]

These serve as spacers to the cutter centre and can

be inserted at different locations - see image

[6]

7.8 Dust extraction

At the extractor connector

[1-15]

, a Festool mobile

dust extractor with an extraction hose diameter of

27 mm can be connected.

7.9 Widening the contact surface

The contact surface widening device

[7-1]

can be

used to enlarge the contact surface when routing

on the workpiece edge, thus allowing safer guid-

ance of the machine.



Secure the contact surface widening device us-

ing the two screws

[7-2]

on the threaded holes

[7-3]

of the guide frame.

The contact surfaces of the contact surface wid-

ening device

[7-5]

and the table

[7-4]

must be

level.

8 Working with the machine

Wood is a natural, non-homogenous material and

because of this, its dimensions will most likely de-

viate slightly during processing, even if the machine

is set accurately. Machine handling also influence

the degree of working accuracy (e.g. fast-feed

speed). Furthermore, the dimensions of wooden

DOMINOs may vary (for example, due to humidity),

regardless of how they are stored. All of these fac-

tors influence the dimensional accuracy of manu-

factured dowel holes and dowelling joints.



We recommend

routing and joining a test work-

piece before machining the actual workpiece.

Please observe all mentioned safety infor-

mations and the following rules when work-

ing:

– Always secure the workpiece in such a manner

that it cannot move while being processed.

– Always hold the machine with two hands on the

handles

[1-3]

when performing work. This re-

duces the risk of injury and is a prerequisite for

precise work.

– Close the clamp lever for routing height adjust-

ment

[1-14]

and the clamp lever for angle adjust-

ment

[1-12]

to avoid unintentional loosening

during operation.

– Adapt the feed rate to the cutter diameter and

material. Work with a constant feed rate

– Only lay the machine aside when the cutter has

come to a complete standstill.

– Always connect the machine to a dust extractor.

For work that generates dust, wear a dust

mask.

Procedure

Proceed as follows to create a DOMINO dowelling

joint:

Tight fitting dowel 13.5 mm + cutter diameter

Dowel with lateral

play 16.5 mm + cutter diameter

A Three possible spacings to a supply side (1 -

2 - 3)

B Two dowel holes beside each other from a

supply side (1 - 3)

C Two dowel holes by changing the workpiece,

e.g. for cross-section cut.

WARNING

Dust hazard



Dust can be hazardous to health. Always work

with a dust extractor.



Always read applicable national regulations be-

fore extracting hazardous dust.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Festool DF 700 EQ - Dominio XL - 2021 in the language / languages: All languages as an attachment in your email.

The manual is 8.47 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Festool DF 700 EQ - Dominio XL - 2021 Manual

Product: