510174
11
Zoom out
Zoom in
Previous page
1/63
Next page
CXS
11
GB
5.2 Machine-related safety instructions
Hold power tool by insulated gripping surfaces,
when performing an operation where the cut-
ting accessory may contact hidden wiring or its
own cord.
Cutting accessory contacting a "live"
wire may make exposed metal parts of the power
tool "live" and could give the operator an electric
shock.
The charger and power tool are not intended for
use by persons (including children) with limited
physical, sensory or mental ability or without
sufficient experience and/or knowledge, unless
they are supervised by a person responsible for
their safety or have been instructed on how the
charger or power tool is to be used.
Children
should always be supervised to ensure that they
do not play with the charger or the power tools.
Wear suitable protection:
such as ear protec-
tion, safety goggles, a dust mask for work which
generates dust, and protective gloves when
working with raw materials and when changing
tools.
CAUTION! Rebound!
Rotation: Switch off device immediately!
Do not lock the on/off switch permanently!
Do not open the battery pack or the charger!
Prevent metal parts (e.g. metal chips) or fluids
from entering the charger!
Do not use battery packs or chargers from other
manufacturers!
Protect the battery pack from excessive heat or
constant heat sources such as sunlight or naked
flames!
Never use water to extinguish burning li-ion bat-
tery packs! Use sand or a fire blanket.
Check the plug and the cable regularly and
should either become damaged, have them re-
placed by an authorised after-sales service
workshop.
– Always pull the mains plug out of the socket
when the charger is not in use.
5.3 Emission levels
Levels determined in accordance with EN 60745 are
typically:
Vibration emission value a
h
(vector sum for three
directions) and uncertainty K measured in accor-
dance with EN 60745:
The specified emissions values (vibration, noise)
are used to compare machines.
They are also used for making preliminary esti-
mates regarding vibration and noise loads during
operation.
They represent the primary applications of the
power tool.
Increase possible for other applications, with other
insertion tools or if not maintained adequately. Take
note of idling and downtimes of machine!
6Operation
6.1 Changing the battery pack [2]
Battery pack is ready for use immediately upon
delivery and can be charged at any time.
Side of the belt clip
[2-1]
can be replaced when
battery pack is removed.
6.2 Charging the battery pack [3]
The LED
[3-1]
on the charger indicates the respec-
tive operating status of the charger.
Sound pressure level L
PA
= 65 dB(A)
Sound power level L
WA
= 76 dB(A)
Uncertainty K = 3 dB
Wear ear protection.
Drilling in metall a
h
=3,0 m/s
2
K = 1,5 m/s
2
Fastening a
h
=4,0 m/s
2
K = 1,5 m/s
2
LED yellow - continuous light
Charger is ready to use.
LED green - light flashes quickly
Battery pack is charged to maxi-
mum capacity.
LED green - light flashes slowly
Battery pack is charged to 80%
and with reduced current.
LED green - continuous light
Battery pack is charged.
LED red - light flashes
General fault indicator, e.g.
incomplete contact, short circuit,
defective battery pack, etc.
LED red - continuous light
Battery temperature is outside
permissible limit values (0 °C to
45 °C).
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool CXS Li 1.5 Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool CXS Li 1.5 Plus in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info