499158

Festool CTM 36 E AC Manual

15
Zoom out
Zoom in
Previous page
1/100
Next page
CTM
15
GB
7Settings
7.1 Adjusting the hose diameter
Adjust the hose diameter adjuster
[1-9]
to
match the diameter of the connected hose.
The monitoring devices will measure the air
speed in the extractor hose correctly as a result
(see chapter 7.9).
7.2 Connecting electric power tools
Connect the electric power tool to the appliance
socket
[1-4]
.
7.3 Connecting pneumatic tools
Automatic on/off switch for air tools (CTM 36 E LE,
CTM 36 E LE AC, CTM 48 E LE, CTM 48 E LE AC or
accessories)
with compressed air module in module slot
[1-3]
Recommendation:
– Attachment of service unit VE (495886): com-
pressed air filtered and lubricated
– Use of IAS system with IAS connector (454757)
for Festool air tools
Requirement:
tool with operating pressure of
6bar!
7.4 Adjusting the suction power
Use the rotary knob
[1-10]
.
7.5 Applying the brake
Folding out the black brake lever
[1-15]
prevents
the mobile dust extractor from rolling. To achieve
this, lift the front end of the mobile dust extractor
slightly and push the black brake lever downwards
until it latches into place. Push the green lever
[1-
14]
again to release.
7.6 Temperature cut-out
A temperature cut-out switches the mobile dust ex-
tractor off when it reaches a critical temperature to
prevent overheating.
Switch off the mobile dust extractor, allow to
cool for about 5 minutes then switch on again.
Not possible to switch on: contact Festool ser-
vice workshop.
7.7 Changing the filter bag
(SC FIS-CT 26/
36/48)
Removing the filter bag [4]
Open the locking clips
[2-2]
and
remove the top section of the machine
[2-1]
.
Remove the filter bag.
Dispose of the used filter bag in accordance with
statutory regulations.
Clean the dust container
[2-3]
.
Inserting the filter bag [5]
Insert a new filter bag (SC FIS-CT 26/36/48) in
the inlet port of the dust container and interlock
it.
Important:
be aware that the locking engag-
es.
Replace the top section
[2-1]
and close the
locking clips
[2-2]
.
Make sure that the filter bag is not pinched be-
tween the top and bottom sections.
7.8 Changing the disposal bag
Removing the disposal bag [6]
Close off the extractor opening
[1-2]
using the
sealing plug
[1-1]
.
Open the locking clips
[2-2]
and
remove the top section of the machine
[2-1]
.
Close the disposal bag.
Remove the disposal bag.
Dispose of the used disposal bag in accordance
with statutory regulations.
Clean the dust container
[2-3]
.
Inserting the disposal bag [7]
Insert a new disposal bag (ENS-CT26/36/48) on
the inlet nozzle of the container and lock in po-
sition.
Important:
The lateral openings on the disposal
bag must be positioned inside the container.
Make sure that the bolt engages.
Place the disposal bag over the edge of the con-
tainer.
Make sure that the contacts
[10-2]
are free.
Replace the top section
[2-1]
and close the
locking clips
[2-2]
.
WARNING
Risk of injury
Observe the maximum appliance socket con-
nected load (see chapter "Technical data")
Switch off the electric power tool.
WARNING
Risk of injury
Switch off the air tool.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool CTM 36 E AC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool CTM 36 E AC in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info