499155
16
Zoom out
Zoom in
Previous page
1/100
Next page
16
CTM
GB
7.9 Volumetric flow monitoring
An acoustic warning signal sounds if the air speed in the suction hose falls below 20 m/s.
8Working
8.1 Handling
Hose store:
after finishing work, you can feed the
suction hose through the recess
[8-3]
and place it
in the hose store. You can do the same with the
mains cable through the other recess
[8-2]
.
SysDoc Systainer attachment system:
a Systainer
can be attached to the storage area via the two
slides
[8-1]
.
8.2 AUTO
Clean
- Cleaning the main filter
(only versions with AutoClean)
To maintain a constant suction power when extract-
ing fine dust, you can adjust the frequency of the
automatic
[1-8]
cleaning system in infinite vari-
ables using the rotary knob. Always use the auto-
matic cleaning system in combination with a dis-
posal bag (in line with dust class 'M' requirements).
Before performing wet extraction tasks or
working with a filter bag, set the
[1-8]
rotary
knob to position 0.
Set the automatic cleaning function to the high-
est setting when
[1-8]
extracting large quanti-
ties of dust.
Manual cleaning
Turn the switch
[1-11]
to the
AC
symbol.
We recommend cleaning the main filter complete-
ly if severely clogged:
Cover the end of the nozzle or suction hose with
your hand for 2 seconds.
Turn the switch
[1-11]
to the
AC
symbol.
When the CT-VS closing slide is used (order no.:
497926), the filter can be cleaned fully without
removing the connected electric power tools.
In intensive applications that generate adherent
dust, it may be necessary to clean the filter element
mechanically under certain circumstances (ex-
tract). Wear a dust mask!
8.3 Special features of the CTM 36 E AC- LHS
To use the mobile dust extractor in combination
with the
PLANEX
:
Use kink-resistant suction hose D 36 mm x 3.5
m-AS.
Use a special suction sleeve for connecting the
PLANEX
.
Use closing slide CT-VS between the intake
opening
[1-2]
and suction hose.
Attach the tool holder.
Always use with a disposal bag!
8.4 Extracting dry materials
Observe the following
when extracting dust gener-
ated by operating electric power tools:
If the exhaust air is discharged back into the room,
the
air renewal rate L
within the room must be
sufficient. The volume of air discharged back into
the room must not exceed 50% of the fresh air vol-
ume flow (room volume V
R
x air renewal rate L
W
).
Observe all the relevant regional regulations.
Possible causes Solution
Value set on the suction power adjuster
[1-10]
is
too low.
Set the suction power adjuster to a higher value (see
Chapter 7.4).
Rotary knob
[1-9]
not set to the correct hose
diameter.
Set the knob to the correct hose diameter (see Chap-
ter 7.1).
Suction hose blocked or kinked. Remove blockage or kink.
Filter bag full. Insert a new filter bag (see Chapter 7.7).
Filter element clogged. Change the filter element (see Chapter 9.1).
Only AUTO
Clean
:
Clean filter element (see chapter
8.2).
Monitoring electronics malfunction. Send to a Festool service workshop for repair.
Wet extraction. Functional reliability not affected, no actions required.
CAUTION
Hazardous dust
Damage to the respiratory passage
Use a filter or disposal bag when extracting haz-
ardous materials!
Do not use the machine if the volumetric flow
monitoring function is inactive.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool CTM 26 E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool CTM 26 E in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info