499167
18
Zoom out
Zoom in
Previous page
1/122
Next page
18
CTH
GB
5.2 Extracting asbestos dust
After the extractor is used to ex-
tract asbestos dust in a sealed-
off area, it can no longer be used
in the white area. Exceptions are
only permitted if the asbestos
dust extractor has been completely decon-
taminated by an approved specialist. This
must be recorded in writing and signed by
the approved specialist.
Fixed filters may only be replaced in suitable
areas (e.g. decontamination stations) by an
approved specialist.
The applicable national regulations (for
example TRGS 519) may contain fur-
ther provisions that regulate or restrict
the application areas of the mobile
dust extractor and which must be ob-
served when extracting dust contain-
ing asbestos particles.
6 Operation
6.1 Initial operation
X
Open the locking clips
[2-2]
and remove
the top section of the machine
[2-1]
.
X
Remove the accessories from the dust
container
[2-3]
and the packaging!
X
Affix the accompanying sticker in your na-
tional language over the text field on the
warning sign
[1-11]
.
X
Insert the sealing plug
[1-1]
on the panel
(see Fig.
[1a]
).
X
Place a filter bag or safety filter bag in the
dirt trap in accordance with statutory re-
quirements (see Chapter 7.7, 7.8).
X
Replace the top section
[2-1]
and close
the locking clips
[2-2]
.
X
Attach the cable holder to the rear of the
mobile dust extractor (see Fig.
[3]
).
X
Connect the suction hose to the machine.
6.2 Switch on/off
X
Insert the plug into an earthed socket.
The switch
[1-10]
serves as an on/off
switch.
Switch position "0"
Appliance socket
[1-4]
is disconnected from
the power, mobile dust extractor is switched
off.
"MAN" switch position
Appliance socket
[1-4]
is connected to the
power, the mobile dust extractor starts.
"Auto" switch position
Appliance socket
[1-4]
is connected to the
power, the mobile dust extractor starts when
the connected tool is switched on.
7 Settings
7.1 Adjusting the hose diameter
X
Adjust the hose diameter adjuster
[1-8]
to match the diameter of the connected
hose.
L
The monitoring devices will measure the
air speed in the extractor hose correctly
as a result (see chapter 7.9).
7.2 Connecting electric power tools
X
Connect the electric power tool to the ap-
pliance socket
[1-4]
.
WARNING
Unauthorised voltage or frequency!
Risk of accident
X
The mains voltage and the frequency of
the power source must correspond with
the specifications on the machine's name
plate.
X
In North America, only Festool machines
with the voltage specifications 120 V/60
Hz may be used.
WARNING
Risk of injury from tools starting up un-
expectedly
X
Before setting the switch to the "AUTO" or
"MAN" position, make sure that the con-
nected tool is switched off.
WARNING
Risk of injury
X
Observe the maximum connected loads
for the appliance socket (see chapter
"Technical data").
X
Make sure that the power tool is switched
off before connecting or disconnecting.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool CTH 48 E a at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool CTH 48 E a in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info