499154
14
Zoom out
Zoom in
Previous page
1/93
Next page
14
CLEANTEX
GB
6.2 Switch on/off
X
Insert the plug into an earthed socket.
The switch [1-7] serves as an on/off switch.
Switch position "0"
Appliance socket [1-3] is disconnected from
the power, mobile dust extractor is switched
off.
"MAN" switch position
Appliance socket [1-3] is connected to the
power, the mobile dust extractor starts.
"Auto" switch position
Appliance socket [1-3] is connected to the
power, the mobile dust extractor starts when
the connected tool is switched on.
7 Settings
7.1 Connecting electric power tools
X
Connect the electric power tool to the ap-
pliance socket [1-3].
7.2 Connecting pneumatic tools
If the compressed air module [1-2] (496141)
is installed, the automatic switch-on function
of the mobile dust extractor also works in
combination with pneumatic tools.
We also recommend installing the VE service
unit (495886). The service unit filters and lu-
bricates the compressed air and enables an
adjustment of the air pressure. An IAS
adapter (454757) is available to connect Fes-
tool pneumatic tools to the IAS system.
The operating pressure of the tool must be
6 bar for the automatic switch-on unit to
function correctly.
7.3 Adjusting the suction power
You can use the suction power adjuster [1-8]
to adapt the machine suction power to differ-
ent applications.
7.4 Applying the brake
Folding out the black brake lever [1-12] pre-
vents the mobile dust extractor from rolling.
To achieve this, lift the front end of the mo-
bile dust extractor slightly and push the
black brake lever downwards until it latches
into place. Push the green lever [1-11] again
to release.
7.5 Temperature cut-out
To prevent overheating, a temperature cut-
out switches the mobile dust extractor off
when it reaches a critical temperature.
X
Switch off the mobile dust extractor and
allow to cool for about 5 minutes.
L
If the mobile dust extractor will not switch
on again, please contact a Festool service
workshop.
8 Working
8.1 Handling
Hose store:
after finishing work, you can
feed the suction hose through the recess [4-
3] and place it in the hose store. You can do
the same with the mains cable through the
other recess [4-2].
SysDoc Systainer attachment system:
a
Systainer can be attached to the storage
area via the two slides [4-1].
8.2 Extracting dry materials
The filter element will become damp when
fluids are extracted. A damp filter element
will clog more quickly when dry materials are
extracted. Therefore, dry the filter element
before extracting dust or replace the damp
filter with a dry one.
8.3 Extracting fluids
Before extracting fluids, remove the filter or
disposal bag (see chapter 9.1). We recom-
mend using a special wet filter.
WARNING
Risk of injury from tools starting up un-
expectedly
X
Before setting the switch to the "AUTO" or
"MAN" position, make sure that the con-
nected tool is switched off.
WARNING
Risk of injury
X
Observe the maximum connected loads
for the appliance socket (see chapter
"Technical data").
X
Make sure that the power tool is switched
off before connecting or disconnecting.
WARNING
Risk of injury
X
Make sure that the pneumatic tool is
switched off before connecting or discon-
necting.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool CT 36 E HEPA CLEANTEX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool CT 36 E HEPA CLEANTEX in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info