Manual Festool CS70EB-S PR (page 17 of 110) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

573129

Zoom out

Zoom in

1/110

P R E C I S I O -

Temperature cut-out

The machine power supply is limited and the

speed reduced if the motor exceeds a certain

temperature. The machine continues operating

at reduced power to allow the ventilator to cool

the motor quickly. The machine starts up again

automatically once the motor has cooled sufﬁ -

ciently.

Brake (CS 70 EB only)

After the machine switches off, the saw blade

is electronically brought to a standstill in 3 sec-

onds.

Restart protection

The integral undervoltage release prevents the

machine from automatically starting up again

after an interruption in power when the machine

is used in continuous operating mode.

The machine will have to be switched back on in

this case.

7.2 Set-up position

Always move the saw to set-up position before

making any adjustments:

The saw is locked in rest position on delivery.

Turn the rotary knob [2-6] anticlockwise to re-

lease the lock and pull the saw forwards.

Push the stop lever [1-7].

The saw is locked in the front position.

7.3 Adjusting the cutting depth

Proceed as follows to adjust the cutting depth in

set-up position to any setting between 0 - 70mm:

Turn the cutting depth adjuster [1-8].

 Set a cutting depth 2 - 5 mm greater than the

thickness of the workpiece to produce an ac-

curate cut.

7.4 Adjusting the mitre angle

The saw blade can be tilted between 0° and 45°

in set-up position:

Unscrew the rotary knob [2-4].

Adjust the mitre angle using the rotary handle

[2-3] with reference to the scale [2-5].

Tighten the rotary knob [2-4].

The saw blade can be tilted 2° beyond the two

end positions for precision trimming work (un-

dercuts on abutting edges).

Press and hold the button [2-2] in the end po-

sition.

The saw blade can now be tilted from -2° to 47°

using the rotary handle [2-3]. Release the button

[2-2] to reactivate the 0° and 45° stops.

7.5 Changing tools

Removing saw blades

Lock the saw in set-up position.

Set the widest inclination angle and the maxi-

mum cutting depth.

Loosen the clamp on the insert via the rotary

knob [5-1].

Slide the clamping plate forwards.

Reach underneath the table insert [1-4] from

the back and remove by lifting away from the

back of the table.

Remove the protective cover.

Swivel the cover [5-10] backwards.

Remove the hexagon wrench [5-3] from the

store on the base [5-6] and insert in the saw

blade retaining screw.

Press and hold the spindle stop [5-2] (behind

the saw blade) and use the hexagon wrench to

turn the saw shaft until the spindle stop [5-2]

engages and the saw shaft locks.

 The saw blade retaining screw has a left-

handed thread.

Firmly turn the saw blade retaining screw

clockwise and remove the clamping ﬂ ange

and the saw blade.

Installing saw blades

WARNING

Risk of injury

Observe the rotation direction when attach-

ing a new saw blade: the rotation direction on

the saw blade [5-4] must correspond with the

rotation direction on the machine.

Place the saw blade in position.

Secure the saw blade and the ﬂ ange to the

saw shaft using the saw blade retaining screw.

Close the cover [5-10] and ﬁ t the protective

cover.

Make sure that the cover [5-10] engages in the

tabs [5-9].

Replace the hexagon wrench [5-3] back in the

store.

Fitting the table insert [1-4] in the table

Insert the protruding spring plate [5-5] on the

insert forwards into the table frame ﬁ rst. Make

sure that the contact surface is free of dust.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Festool CS70EB-S PR in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,7 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Festool CS70EB-S PR Manual

Product: