Manual Festool CS5--ST22 (page 7 of 26) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

573134

Zoom out

Zoom in

1/26

Sliding table ST

The sliding table consists of a guide rail

(4.2) which is mounted to the left side of the

CS 50 EB/CMS GE/ MFT/3-VL and a carriage (4.1)

which slides on the guide rail.

For transport, the slide can be ﬁ xed to the guide

rail using the rotary knob (3a.5).

Stop WRA 500 can be attached to the curved

groove on the carriage at the same time as the

CS 50 EB/CMS GE.

Fitting CS 50/ CMS-GE

– Attach one bracket at each of the two external

recesses (1.1) on the base chassis using the peg

(1.2).

Caution: the protruding points (1.3) on each of

the brackets must point outwards.

– Slide the brackets into the groove (1.6) until the

outer edge (with protruding points) lines up with

the join (1.4) on the base frame and the snap-

on clips lock onto the protruding points in the

groove.

– Lower the guide rails into position at an angle,

locating both plastic brackets (2.1) in the groove

(2.2) on the saw table.

– Swivel the guide rails downwards so that the

pegs (1.5) on the brackets engage in the holes

(2.3) on the guide rails.

Note: the guide rail has three drilled holes and

can therefore be secured in two positions (pro-

truding point to the rear or front).

– Secure the guide rails using the two rotary knobs

(3a.3).

– Slide the carriage with the four rollers (3a.4)

onto the guide rails from the side as shown in

Fig. 3a.

– Secure the end stops (3a.1) at both ends of the

groove (3a.2).

Fitting MFT/3-VL

– Insert the guide rail into the groove (3b.1) on the

extension at an angle from above with the two

plastic brackets (2.1).

– Lower the guide rail so that the rotary knobs on

the guide rail (3b.3) engage in the holes (3b.2)

on the extension.

Note: the guide rail has three drilled holes and

can therefore be secured in two positions (pro-

truding point to the rear or front).

– Secure the guide rails using the two rotary knobs

(3b.3).

– Slide the carriage with the four rollers (3a.4)

onto the guide rails from the side as shown in

Fig. 3a.

– Secure the end stops (3a.1) at both ends of the

groove (3a.2).

Height adjustment

– Unscrew both rotary knobs (3a.3).

– Turn both Allen screws (4.3) until the sliding

fence is approx. 1 mm above the saw table.

– Tighten the rotary knobs (3a.3).

Angle adjustment

– Angle adjustment

– Open both screws (5.1).

– Turn the screw (5.2) until the contact surface of

the slide is parallel to the table surface of the

bench circular saw. Check the parallelism by

placing a straight ruler over the slide and the

table of the bench circular saw.

– Close both screws (5.1).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Festool CS5--ST22 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Festool CS5--ST22 Manual

Product: