Manual Festool CS 50 EB Floor (page 20 of 110) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

498002

Zoom out

Zoom in

1/110

wedge and clamping element again and tighten

all screws.

6.5 Guide

As shown in Fig. 3, the supplied guide can be se-

cured to all four sides of the machine. The guide

offers the following adjustment options:

• Adjustment parallel to the bench edge - open

the rotary knob (3.5).

• Adjustment vertical to the bench edge - open

the rotary knob (3.6).

• Adjustment of the sliding fence (3.1) in a longitu-

dinal direction - open the rotary knob (3.2). The

sliding fence can be clamped onto the holder in

a low position for thin workpieces (Fig. 1), or in

a high position for thick workpieces (Fig. 3).

• Angle adjustment using the scale (3.7) - open

the rotary knob (3.3) and raise the ﬁ xing pin

(3.4). The rotating ﬁ xing pin locks into place in

the most common angle positions.

This means that the guide can be used as a par-

allel guide (Fig. 1) or as a cross guide or angle

guide (Fig. 3).

Prior to all work, make sure that all rotary

knobs of the guide are tightened. The

guide may only be used in a ﬁ xed position

and not to shift the workpiece.

6.6 Scale for cutting width

The two scales (1.5) specify the cutting width for

longitudinal cuts.

If required, the scales can be realigned after open-

ing the screws (1.4).

6.7 Mounting the splinterguard

The splinterguard (10.2) prevents breakouts on

the lower cutting edge of the workpiece.

The splinterguard can be used for all mitres, but

a separate splinterguard must be ﬁ tted and sawn

in for each angle:

- Set saw blade to minimum cutting depth.

- Open the locking mechanism (1.3) and remove

the bench insert (1.2) upwards.

- Open the locking mechanism (6.1) and swing the

saw blade cover (6.2) down. This automatically

locks the tool spindle.

- Push splinterguard (10.2) from the side into the

holder (10.3) up to the stop.

- Swing the saw blade cover (6.2) upwards and

close the locking mechanism (6.1).

- Insert the bench insert with the rear edge ﬁ rst

(see Fig. 9) and close the locking mechanism

(1.3).

- Switch on tool and slowly move the saw blade

up to the maximum cutting depth – this cuts the

splinterguard to shape.

For a optimum function the raised part (10.1) of

the splinterguard should protrude slightly (approx.

0.3 mm) above the surface of the base runner. For

this purpose the height of the holder (10.3) can be

adjusted after releasing both screws (10.4).

7 Working with the machine

When working with the machine, comply

with all safety instructions.

Adjust the protective hood so that it rests on the

workpiece and clamp it in this position with the

knob (1.1).

7.1 Bench-mounted circular saw

Use the guide as a parallel guide (Fig. 1) to guide

the workpiece. The cutting width can be set using

the scales (1.5). Guide the workpiece into place by

hand. Use the workpiece holder (2.4) to guide the

workpiece safety past the saw blade. When not in

use, place the work-piece holder in the storage

compartment (2.1).

7.2 Circular trimming saw

Use the guide as a cross guide or as an angle

guide (Fig. 3) to apply and secure the work-piece.

Alternatively, clamps (489570) can be inserted in

the grooves (3.8) to secure the workpiece. Perform

the sawing cut by swinging the hand grip (3.9)

downwards and using the hand grip to pull the

saw unit forwards. After making the sawing cut,

move the saw unit right back again into its initial

position before you take the workpiece from the

guide.

8 Maintenance and care

Prior to any setting, maintenance or re-

pair, pull the mains plug!

All maintenance and repair work which

requires the motor casing to be opened

may only be carried out by an authorised

service centre.

Damaged safety devices and parts should

be repaired or replaced by an authorised

service centre unless otherwise speciﬁ ed

in the operating instructions.

The routers are ﬁ tted with special carbon brushes

with automatic-switch-off. When the brushes

reach their wear limit the current is interrupted

automatically and the router comes to a stand-

still.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Festool CS 50 EB Floor in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,99 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Festool CS 50 EB Floor Manual

Product: