574904
14
Zoom out
Zoom in
Previous page
1/86
Next page
14
1. Speed: Lever forward - Figure 1 is visible.
2. Speed: Lever backwards - Figure 2 is
visible.
2.4 Torque adjustment
By turning the adjustment ring (1.6) the
required torque can be adjusted. The arrow
(1.7) aligns with the adjusted state.
The machine switches off when the set torque
has been reached. The machine does not
start running again until the ON/OFF switch
(1.3) is released and then pressed again.
Drilling
Drilling symbol on adjustment ring aligns
with the arrow = maximum torque.
Screws
Torque corresponding to setting:
Position 1 = low torque
Position 20 = high torque
3 Tool holding xture, attachments
3.1 Chuck BF-FX
The chuck is used to clamp drills and bits.
a) Fitting/removing the chuck
Fitting
- Place the chuck on the drill spindle (2.5)
and twist until the hexagon key (2.4) of
the chuck latches into the hexagon socket
of the drill spindle.
- Pull the unlocking ring (2.3) forwards,
press the chuck onto the drill spindle up to
the stop and release the unlocking ring.
Removal
- Pull the unlocking ring forwards and re-
move the chuck.
b) Changing tools
- Turn the clamping sleeve (2.2) anti-clock-
wise to open the clamping jaws (2.1)
(Note: the spindle is automatically locked
when the machine is switched off).
- Insert the tool into the chuck.
- Clamp the tool by turning the clamp-
ing sleeve clockwise. Always make sure
that the tool is clamped centrally in the
chuck.
3.2 Angle attachment DD-AS
The angle attachment permits work (drilling,
screwing) vertical to the machine’s longitu-
dinal axis.
a) Fitting/removing the angle at-
tachment
Fitting
- Place the angle attachment on the drill
spindle and turn until it catches in the
desired position (Note: The angle attach-
ment can be tted in 16 different angle
settings).
- Lock the angle attachment by turning the
fastening ring (2.7) tightly clockwise.
Removal
- Turn the fastening ring anti-clockwise up
to the stop and remove the angel attach-
ment.
b) Fitting/removal of chuck on an-
gle attachment
The chuck is tted on the shaft (2.6) of the
angle attachment in the same way as on the
drill spindle of the machine.
3.3 Eccentric attachment DD-ES
The eccentric attachment is used to hold
bits. It allows screwing close to edges.
a) Fitting/removing the eccentric
attachment
The eccentric attachment is tted/removed
in the same was as the angle attachment
(see Chapter 3.2).
b) Changing tools
- Pull the unlocking ring (2.8) back and re-
move the tool and/or insert the new tool.
3.4 CENTROTEC WH-CE toolholder
The CENTROTEC toolholder enables rapid
changes of tools with CENTROTEC shafts.
Do not t CENTROTEC tools at the
round shaft section in a conventional
chuck to prevent damage to the
shaft.
Danger of injury! When changing
tools, handle the tool and its sharp
cutters with special care and wear
protective gloves, if necessary.
a) Fitting/removing CENTROTEC
Fitting
- Pull the release ring (2.11) forwards, place
the toolholder as far as it will go on the drill
spindle (2.5) and let go of the release ring.
Removal
- Pull the release ring forwards and take off
the toolholder.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool C12-12.0 V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool C12-12.0 V in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info