497582
15
Zoom out
Zoom in
Previous page
1/90
Next page
C 12 Li, C 15 Li
15
GB
An
acoustic signal
sounds when the preset torque
is reached and the machine then switches off. You
must release and press the ON/OFF switch
[1-9]
again to start the machine.
7.4 Drilling
Adjust the switch so that its marking
[1-7]
faces
the drilling symbol
[1-5]
= maximum torque.
8 Tool holder, attachments
8.1 CENTROTEC tool chuck [4]
Quick change of tools with CENTROTEC shaft
Only clamp CENTROTEC tools in CENTRO-
TEC tool chucks.
Wear gloves when replacing!
8.2 Chuck BF-FX [5]
For clamping drill bits and bits with max. shaft di-
ameter of 13 mm.
Clamp tool centrally in the chuck.
8.3 Angle attachment DD-AS [6]
Drilling and screwing at right angle to machine
(partly as an accessory).
8.4 Eccentric attachment DD-ES [7]
Screwdriving near edges with bits according to ISO
1173 (partly as accessory).
8.5 Tool holder in the drill spindle [8]
Bits can be inserted directly into the hexagon sock-
et holder of the drill spindle.
9 Working with the machine
9.1 On/Off switch [1-9]
Press = ON, release = OFF
The speed of the machine depends on how far
the on/off switch is pressed in.
The LED bulb
[1-3]
lights up when the ON/OFF
switch is pressed
[1-9]
.
9.2 Bit depot [1-2]
Magnetic, for storing bits and bit holders.
9.3 Acoustic warning signals
Acoustic warning signals sound and the machine
switches off in the following operating states:
10 Service and maintenance
Observe the following instructions:
Keep the air slits on the machine and the charger
free and clean to ensure adequate cooling.
Keep the contacts on the machine, charger and
battery pack clean.
Information on battery packs
Where possible, store the battery pack in a cool,
dry place at a temperature between 5 °C and 25
°C.
Battery packs are most efficient at temperatures
between 20 °C and 30 °C.
Protect the battery pack from moisture, water
and heat.
Significantly shorter operating times after each
charge indicate that the battery pack is worn and
should be replaced with a new one.
The LiIon battery pack is fully compatible with the
charger! Integrated electronics prevent over-
loading and overheating during the charging pro-
cess.
Do not leave flat battery packs in a charger dis-
connected from the mains power supply for lon-
ger than one month. There is a risk of total
discharge and the maximum power of the battery
pack may decrease.
Store the battery pack in its packaging to reduce
the risk of short circuits..
If LiIon battery packs are to be stored for long pe-
riods without use, they should be charged to 40 %
capacity (approx. 15 mins. charging period).
11 Accessories
The order numbers of the accessories and tools can
be found in the Festool catalogue or on the Internet
under "www.festool.com".
WARNING
Risk of injury, electric shock
Always disconnect the battery pack before any
type of work on the machine!
Battery flat or machine over-
loaded.
Change the battery.
Place the machine under reduced
stress.
Machine is overheating.
You must allow the machine to
cool beforeusing again.
LiIon battery pack is faulty or has
overheated.
Once the battery pack has cooled,
perform a functional check using
the charger.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool C 12 Li at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool C 12 Li in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info