778636
14
Zoom out
Zoom in
Previous page
1/76
Next page
Accessories shown or described are not always
included in the scope of delivery.
The specified illustrations appear at the begin
ning of the Operating Instructions.
6 Commissioning
WARNING
Unauthorised voltage or frequency.
Risk of accidents
Observe the specifications on the ma
chine's name plate.
Observe country-specific regulations.
6.1 Changing the battery pack
Inserting the battery pack [2 A]
Removing the battery pack [2 B]
6.2 Lighting and battery capacity indicator
The LED [1-10] provides light and acts as
a battery capacity indicator [1-9].
When the on/off switch [1-4] is pressed, the
LED automatically displays the state of charge
of the battery pack (not for NiCd and NiMH bat
tery packs).
Green LED – steady light:
State of charge > 60%
Green LED – flashing
slowly: State of charge
30%–60%
Green LED – flashing
quickly: State of charge
0%–30%
Yellow LED – steady light:
Battery is flat
Red LED – steady light:
Temperature of the bat
tery, electronics or motor
is outside the permitted
range.
Red LED – flashing: Gen
eral fault indicator, e.g. not
in full contact, short cir
cuit, faulty battery pack,
etc.
When the battery pack is empty, or if there
is a power failure or the mains plug is re
moved, move the on/off switch immediate
ly to the Off position. This prevents uncon
trolled restarting.
Further information about the charger and
battery pack with capacity indicator can be
found in the corresponding operating
manual.
7 Settings
7.1 Changing direction of rotation [1-3]
Switch to the left = clockwise rotation
Switch to the right = counterclockwise rota
tion
7.2 Selecting the operating mode
Hammer drilling
Set selector switch [1-5] to hammer
symbol.
Screwdriving/drilling
Set selector switch [1-5] to drill symbol.
8 Tool holder, attachments
WARNING
Risk of injury
Remove the battery pack from the power
tool before performing any work on the
power tool.
8.1 Changing tools [3]
Drills are clamped by means of the SDS-
plus system without using a wrench.
CAUTION
Hot and sharp tools
Risk of injury
Do not use any blunt or defective insert
tools.
Wear protective gloves.
Inserting the tool
Clean the tool shank and apply a coating of
multipurpose grease.
Do [1-2] not retract the release sleeve, but
insert the tool in the tool holder [1-1] and
turn until it engages.
Check that the tool is seated correctly.
Removing the tool
Push the unlocking sleeve [1-2] back and
remove the tool.
8.2 CENTROTEC tool chuck [4]
Quick change of tools with CENTROTEC shaft
Only clamp CENTROTEC tools in CEN
TROTEC tool chucks.
English
14
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Festool BHC 18 Li - 2021 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Festool BHC 18 Li - 2021 in the language / languages: All languages as an attachment in your email.

The manual is 3.25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info