724613
43
Zoom out
Zoom in
Previous page
1/48
Next page
AFTER SALES SUPPORT
(toll free)
224cc 4 Stroke Petrol Lawn Mower
e-mail: info.aldi@positecgroup.com1300 889 028
MODEL No.: SLM530 • 08/2019 • 10093
41
Troubleshooting
Problem
Possible Cause Solution
Engine does not start. Fuel tank (25) is empty.
Oil tank is empty.
Spark plug (27).
Blades hitting the grass to
be cut.
20V Xnity Li-ion battery (8)
is at.
Check the fuel tank (25), and refuel if required.
Check the level of the oil ller cap/dipstick (24), and if low or empty,
add oil.
Clean or replace if dirty or worn.
Increase the cutting height of the mower so the blades do not make
contact with
the grass on start up
Charge the 20V Xnity Li-ion battery (8).
Cutting / Engine
performance
decreases.
Cutting height.
4 x blades (30) are dull or
blunt.
When using side discharge
chute (20).
Hard catcher (43) is full.
Increase the cutting height using the
8 height adjustment lever (18).
Replace the blades with new / sharp blades.
Clean around the side ejector chute.
NOTE: Always ensure the engine is turned
o before undertaking this task.
Empty hard catcher (43).
Hard catcher is not
lling up to optimum
level.
Cutting height too low.
When Mulching, piles of grass
are left behind the mower.
Grass is wet.
4 x swing blades (30) are dull
or blunt
Rear discharge chute (16) is
blocked.
Increase the cutting height using the
8 height adjustment lever (18).
Lift the height of the cutting depth by one notch using the 8 height
adjustment lever (18).
Allow the grass to dry before mowing.
Sharpen or replace the 4 x blades (30).
Stop mower and clear the rear discharge chute (16).
Mower cannot be
pulled backward.
Gearbox is engaged. Release the self propel engage / disengage bar (2).
Self propel does not
operate.
Gear box not engaged.
Engine not operating.
Fully lift self propel engage / disengage bar (2) against the upper
handle bar (1)
Start motor and retry.
Engine does not stop Key failure The safest method is to wheel the lawn mower to a safe area and allow
the lawn mower to continue to run until the fuel has been all used up.
Refer to the Emergency stopping section on page 29 for more detail.
Troubleshooting
Service Support
If you have any issues with the operation of your product, please take it with a copy
of your receipt to one of our National Service Agents for repair. A listing of our Service
Agents is included with your product, however, you can also nd our most updated
listing by visiting https://help.tools/ and clicking on the Service Agent link. Alternately
call us on our Customer Support line, 1300 889 028, for advice or support.
43


Need help? Post your question in this forum.

Forumrules
1

Forum

ferrex-slm530

Reset search

  • I am trying to replace belt on self propelled mower! can anyone tell me how to do this?

    Thannkyou Submitted on 5-6-2022 at 07:54

    Reply Report abuse
  • self drive inoperative with motor running and lever fully engaged Submitted on 25-12-2021 at 01:52

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferrex SLM530 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferrex SLM530 in the language / languages: English as an attachment in your email.

The manual is 10,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info