Manual Ferrex SBV521 (page 14 of 40) (English)

724595

Zoom out

Zoom in

1/40

User Manual

Product

Info

51.7CC 2 STROKE

PETROL BACKPACK

BLOWER

https://help.tools

Read all safety warnings and all instructions thoroughly before operating this product.

Ensure you keep your manual in a safe place for future reference.

IM Ed4 02/2020

13177

QR codes take you where you want to go

quicky and easily

Whether you require product information, spare parts or accessories,

details on warranties or after sales service, or if you want to watch

a product demonstration video, our QR codes will take you there in

no time at all.

What is a QR code?

A QR-code (QR=Quick Response) is a type of matrix that can be read

with a smartphone camera and that contains a link to a website or

contact details, for example.

Advantage: You are not required to manually enter a website address

or contact details.

How it works

To scan the QR code, all you need is a smartphone with QR codes

reader

software and an Internet connection*. This type of software can be

downloaded for free from your smartphone’s app store.

Try it out now

Just scan the QR code with your smartphone and

nd out more about the Aldi product you have

purchased*.

* Depending on your tari you may be charged for the connection.

Product

Info

Contents

Pack contents / parts 2

Description of symbols 3

General Safety Warnings 4

Additional safety rules for Petrol Blowers 9

Parts List 11

Assembly 14

Preparation 19

Operation 23

Maintenance 29

Storage and Transportation 32

Environmental Protection 32

Noise and vibration 33

Warranty 34

Troubleshooting 36

Specications 37

Pack contents / parts

Congratulations on the purchase of your Ferrex® 51.7cc 2 Stroke Petrol Backpack

Blower. When you open your packaging, rst remove all items and check there

are no parts damaged or missing. If you nd anything wrong, do not operate the

product until the parts have been replaced or the fault has been rectied. Failure

to do so could result in serious personal injury.

Intended use of 51.7cc 2 Stroke Petrol Backpack Blower

NOTE: This product is for private domestic DIY use only. It is not suitable for

commercial or trade use.

This 51.7cc 2 Stroke Petrol Backpack Blower is designed for moving leaves and

other garden debris; perfect for patios and driveways.

IMPORTANT INFORMATION.

NOTE: This is a 51.7cc 2 Stroke Petrol Backpack Blower. The fuel tank must be

lled with a 40:1 mix of fuel and 2 stroke oil. Fresh unleaded fuel must be used in

this unit.

Do NOT use Ethanol based fuels. Use good quality 2 Stroke oil.

NOTE: First time users or inexperienced operators pay particular attention to the

operation of the Blower, including details of starting and stopping and correct

use of the Blower on pages 23-27, as well as the maintenance instructions on

pages 28-30.

Contents of carton

1 x 51.7cc Petrol Backpack Blower

1 x Flexible pipe with 2 adjustable

clamps (not tted)

1 x Upper blow tube with tting clamp

ring for throttle handle (not tted)

1 x Middle blow tube with

assembly screw (not tted)

1 x Lower blow tube with

assembly screw (not tted)

1 x Throttle control handle (not tted)

1 x Socket spanner for spark plug

1 x Combination screwdriver

(Philips / slot type)

1 x Fuel / Oil mixing bottle

1 x Instruction manual

1 x Warranty Card & Certicate

1 x Quick Start Guide

Description of symbols

The instruction manual, rating plate, or on the product itself, may show

these symbols. These represent important information about the product or

instructions on its use.

Read instruction manual before operating this machine

Keep bystanders away. Beware of objects being ung out. Use at a distance of at

least 15m from other people.

Warning of hazard. Risk of hand and feet injuries.

Warning

Explosive material

Extremely hot surface. Do not touch a hot muer, gear box or cylinder, you may

get burned. These parts get extremely hot from operation and remain hot for a

short time after the unit is turned o.

Conforms to relevant standards for electrical safety and electromagnetic compatibility.

Wear breathing protection. Wear hearing protection. Wear eye protection

Do not put in water or expose to rain.

Wear protective gloves

Wear protective footwear

60 Months Warranty (5 years)

General safety warnings

Safety instructions

WARNING! Read and understand all instructions. Failure to

follow all instructions listed below may result in electric

shock, re and/or serious injury.

The term “power tool” in all of the warnings below refers to your mains-

operated (corded) power tool, garden power tool, battery-operated

(cordless) power tool or your petrol operated garden tool.

Save these instructions

Work area

• Ensure the area to be blown is clear and free of debris, rocks, gravel,

garden furniture etc.

• Keep work area clean and well lit. Cluttered and dark areas invite

• accidents.

• Do not operate power tools in explosive atmospheres, such as in

the presence of ammable liquids, gases, or dust. Power tools create

sparks which may ignite the dust or fumes.

• Ensure all animals, children and bystanders are at least 20m away

while operating this blower. Distractions can cause you to lose control.

Personal safety

• Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired

or under the inuence of drugs, alcohol, or medication. A moment of

inattention while operating power tools may result in serious personal

injury.

• Use safety equipment. Always wear eye protection. Safety equipment

such as a dust mask, non-skid safety shoes, hard hat, or hearing pro

tection used for appropriate conditions will reduce personal injuries.

• Remove any adjusting key or spanner before turning the tool on. A span-

ner or a key that is left attached to a rotating part of the power tool may

result in personal injury.

• Do not overreach. Keep proper footing and balance at all times. This ena

bles better control of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or jewellery. Keep your hair,

clothing and gloves away from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

• If devices are provided for the connection of dust extraction and collection

facilities ensure that these are connected and properly used. Use of these

devices can reduce dust-related hazards.

Power tool use and care

• Do not force the power tool. Use the correct power tool for your applica-

tion. The correct power tool will do the job better and safer at the rate for

which it was designed.

• Do not use the power tool if the switch does not turn it on and o. Any

power tool that cannot be controlled with the switch is dangerous and

must be repaired.

• Turn tool o completely before making any adjustments, changing acces

sories, or storing power tools. Such preventive safety measures reduce the

risk of starting the power tool accidentally.

• Store idle power tools out of the reach of children and do not allow per

sons unfamiliar with the power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands of untrained users.

• Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may aect the power tool’s

operation. If damaged, have the power tool repaired before use. Many ac

cidents are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly maintained cutting tools with

sharp cutting edges are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits etc., in accordance with these

instructions and in the manner intended for the particular type of power

tool, taking into account the working conditions and the work to be per

formed. Use of the power tool for operations dierent from intended could

result in a hazardous situation.

Safety rules for Petrol Backpack Blowers

Training

• Read the instructions carefully. Get familiar with the controls and proper

use of the equipment.

• Non-skilled persons and rst time users should read and understand the

full instruction manual before proceeding with use of the product or

recommended maintenance tasks.

• Only use the blower for the purpose for which it was designed, i.e.

blowing garden debris. Any other use can be hazardous, causing dam

age to the machine.

• Never allow children or people unfamiliar with these instructions to use

the blower. Local regulations may restrict the age of the operator.

• Never use the blower:

– When people, especially children, or pets are nearby.

– If the operator has taken medicine or substances that can aect his abil

ity to react and concentrate.

• Remember that the operator or user is responsible for accidents or haz

ards occurring to other people or their property.

• Do not use unit around people with long hair.

• Dress appropriately. Do not operate with loose clothing or jewellery.

Ensure there is a gap between the air intake and the operator.

Preparation

• While blowing always wear sturdy non-skid footwear and long trousers.

Do not operate the equipment with bare feet or open sandals.

WARNING: DANGER!

Engine fuel is highly ammable:

– Store fuel in containers specically designed for this purpose.

– Refuel using a funnel and outdoors only. Do not smoke while refuelling

or whenever handling the fuel.

– Add fuel before starting the engine. Never remove the cap of the fuel

tank or add fuel while the engine is running or when the engine is hot.

– If fuel is spilled, do not attempt to start the engine but move the ma

chine away from the area of spillage and avoid creating any source of igni-

tion until the fuel has evaporated and the vapour dispersed.

– Replace all fuel tanks and containers caps securely.

• Substitute faulty silencers.

• Before use, always inspect the machine and check that the screws are not

worn or damaged.

• It is advisable to wear suitable eye protection (safety glasses) ear protec

tion, and sturdy gloves when operating the blower.

• Always check for any objects that may block the air intake screen before

beginning work. A clogged air intake reduces the machine’s blowing ca

pacity and increases the engine’s working temperature, which can result in

engine failure. Stop the engine and remove the object.

Maintenance and storage

• Keep all nuts, bolts and screws tight to be sure the equipment is in safe

working condition. Regular maintenance is essential for safety and perfor

mance.

• Never store the equipment with fuel in the tank inside a building where

vapour may reach a ame or a spark or a source of extreme heat i.e a water

heater.

• Allow the engine to cool before storing in an enclosed space.

• To reduce the re hazard, keep the engine, exhaust silencer, battery

compartment (if applicable) and fuel storage area free of grass, leaves, or

excessive grease.

• If the fuel tank has to be drained, this should be done outdoors and when

the engine is cool.

• For reasons of safety, do not use the equipment with worn or damaged

parts. Parts are to be replaced and not repaired. Parts that are not of the

same quality can damage the equipment and be dangerous for your

safety.

• Fuel goes o fairly quickly. If you nd your blower does not start, rst

change the fuel in the tank with newly purchased fuel.

Service

• Have your power tool serviced by a qualied repair personnel using only

identical replacement parts (recoil starter, spark plug, collection bag,

tubes, blades / impellor). This will ensure that the safety of the power

tool is maintained.

Operation safety instructions

WARNING. Stop the engine and unplug the spark plug before

any repairs or maintenance operations.

• This machine is extremely noisy and operators must wear acoustic

protection equipment.

• Rotating parts can cause serious injury, avoid contacting the rotating

parts when is still rotate.

• Try not to cause any disturbance. Use this machine at reasonable

times of the day only (not early morning or late evening when the

noise could cause disturbance).

• Check that all nuts, bolts and screws are well tightened before every

use.

• Do not run the engine in an enclosed and/or poorly ventilated area.

The gas of the engine contains carbon monoxide, which is dangerous

to your health.

• Work only when there is sucient light.

• Do not use the blower when it is raining or when the grass is wet.

• Do not use the blower near open windows due to possible debris

entering.

• Caution must be taken while blowing on slopes.

• Turn o the engine if you must leave the blower unattended.

• Never change the rated speed of the engine in any way.

• Stop the engine and remove the spark plug cover in these cases:

– Before any maintenance, repairing or checking operations.

– If you leave the blower unattended.

– If the blower vibrates in an abnormal way, take the blower to an au

thorised service centre.

– Check the bolts and nuts regularly. Bolts and nuts may vibrate loose

over time.

WARNING: DANGER!

Engine fuel is highly ammable:

• Keep fuel in a fuel can specially made for this purpose.

• Fill the fuel tank with a funnel and outside. Do not smoke or use a mobile

phone during this process.

• Fill with fuel / 2 Stroke oil mix before starting the engine. Never open the

cap of the fuel tank to add fuel / 2 stroke oil mix while the engine is run

ning or still hot.

• Do not start the engine if there is spilt fuel on the blower or in the area sur

rounding. Take the blower away from the zone where fuel has been spilt

and avoid any contact from a hot source as long as the spilt fuel is com

pletely evaporated.

• Tighten the fuel tank cap and fuel can cap tightly.

WARNING: This blower is not suitable for use for children below

the age of 14 years old. Children below the age of 14 years old

should not use, or be in reach of this blower during its operation.

WARNING: If something breaks or an accident occurs while work-

ing, turn o the engine immediately and move the machine away

to prevent further damage; if an accident occurs with injuries or

third parties are injured, carry out the rst aid measures most suitable

for the situation immediately and contact the medical authorities for

any necessary health care. Carefully remove any debris that might cause

damage or harm persons or animals should they not be seen.

Additional safety rules for Petrol Blowers

• Do not operate in a hazardous location. Such areas include where there is

a risk of explosion of petrol fumes, leaking gas or explosive dust.

• Do not operate in a conned area. Exhaust gases, smoke or fumes could

reach dangerous concentrations.

• Protect your blower. This blower is NOT WEATHERPROOF and should not

be exposed to direct sunlight, high ambient temperature and damp, wet

or high humidity conditions.

• Do not smoke while refuelling. This is potentially dangerous as it may

ignite the fuel and cause an explosion.

• Take care not to spill fuel. When refuelling the blower ensure that the

motor has been switched o. Prevent the spilling of fuel as this may

also ignite with the hot motor. Never refuel whilst the engine running.

• Be careful where you store the blower. Store the blower in a dry area

away from ammable liquids.

• Keep your distance. The blower emits exhaust fumes. Ensure bystand-

ers keep a safe distance.

• Fill with Fuel / oil mix before starting the engine. Never open the cap

of the fuel tank to add the fuel / oil mix while the engine is running or

still hot. The engine may overheat and cause damage to the blower.

• Never ll fuel tank indoors. Never ll fuel tank when engine is running

or hot.

• Do not smoke when lling fuel tank.

• Stop the engine before re-fuelling.

• Stop the engine and disconnect the spark plug wire:

– If the blower starts to vibrate abnormally (nd and remove the cause

of the vibration immediately).

• Reduce the throttle before turning o the engine and turn the fuel o

when you have nished blowing.

• The user is responsible for the safety of other people, animals and

objects in the working area. Keep children and domestic animals at a

safe distance while the blower is in use.

WARNING: This blower is not suitable for use for children

below the age of 14 years old. Children below the age of 14

years old should not use, or be in reach of this blower during its

operation.

AFTER SALES SUPPORT

(toll free)

e-mail: info.aldi@positecgroup.com1300 889 028

51.7cc 2 Stroke Petrol Backpack Blower

MODEL: №. SBV521 • 02/2020 • 13177

1. Carry handle

2. Shoulder straps

3. Elbow tube

4. Flexible pipe (with 2 x adjust-

able clamps)

5. Upper blow tube (with tting

clamp ring for throttle handle)

6. Middle blow tube (with assem-

bly screw)

7. Lower blow tube (with assembly

screw)

8. Throttle control handle

9. Spark plug cover

10. Choke knob

11. Fuel tank cap

12. Fuel tank

13. Throttle cable

14. Fixing clip for throttle cable

15. Throttle trigger

16. Stop/Start/MAX speed lever

17. Air lter cover

18. Air lter locking knob

19. Air lter

20. Plastic netting

21. Plastic harness

22. Padded harness

23. Primer bulb

24. Recoil starter

25.

Spark plug

26. Lock knob for xing throttle

handle

27. Clamp gear(s) on clamp ring for

xing throttle handle

28. Lock nut for xing throttle

handle

29. Shoulder strap connection

point(s)

30. Fuel / Oil mixing bottle

31. Socket spanner for spark plug

32. Combination screwdriver

(Philips / slot type)

Parts List

51.7cc 2 Stroke Petrol Backpack Blower

AFTER SALES SUPPORT

e-mail: info.aldi@positecgroup.com

1300 889 028

MODEL: №. SBV521 • 02/2020 • 13177

(toll free)

AFTER SALES SUPPORT

(toll free)

e-mail: info.aldi@positecgroup.com1300 889 028

51.7cc 2 Stroke Petrol Backpack Blower

MODEL: №. SBV521 • 02/2020 • 13177

51.7cc 2 Stroke Petrol Backpack Blower

AFTER SALES SUPPORT

e-mail: info.aldi@positecgroup.com

1300 889 028

MODEL: №. SBV521 • 02/2020 • 13177

(toll free)

Preparation of the blower prior to use

This Petrol Backpack Blower requires some

assembly prior to use. This includes joining of the

blower tubes (4,5,6,7), and securing the throttle

control handle (8) to the upper blow tube (5).

Setting up for use

WARNING: Blower tube installation aects

both blower balance and performance.

Stop the engine before installing or removing the

blower tubes. Never perform any maintenance or

assembly procedures on this machine while the

engine is running.

Assembling the exible pipe (4)

1) Place the blower in an upright position on the

ground or on a sturdy work surface (See Fig A1).

2) Loosen the 2 x adjustable clamps on the exible

pipe (4) using the slot end of the combination

screwdriver (32) by turning the screw on the

clamp in an anti-clockwise direction until they

are loose on each end of the exible pipe (4) (See

Fig. A2)

3) Insert the larger opening end of the exible pipe

(4) over the end of the elbow tube (3) to the end

until it hits the raised ridge on the end of the

elbow tube (3) (See Fig. A3)

4) Secure the adjustable clamp on the exible

pipe (4) using the slot end of the combination

screwdriver (32) by turning the screw on the

clamp in a clockwise direction until it tights. (See

Fig. A4)

5) Before proceeding to add the other tubes for

assembly, the throttle control handle (8) needs to

be assembled onto the upper blow tube (5) rst.

Assembly

A1.

A2.

A3.

A4.

AFTER SALES SUPPORT

(toll free)

e-mail: info.aldi@positecgroup.com1300 889 028

51.7cc 2 Stroke Petrol Backpack Blower

MODEL: №. SBV521 • 02/2020 • 13177

Assembling the throttle control handle (8) to

the upper blow tube (5)

1) Rotate the clamp ring and push it further along

the tube, to ensure the notch on the clamp ring

engages the raised channel on the upper blow tube

(5). (See Fig. B1)

2) Loosen the lock knob (26) for xing throttle handle

by turning it in an anti-clockwise direction. Then

remove the lock knob (26) from the lock nut for

xing throttle handle (28). Be careful not to lose the

lock nut (28). (See Fig. B2)

3) Keep the lock nut (28) in its original hole in the

clamp gear (27) on the clamp ring. Align and insert

the lock knob for xing throttle handle (26) through

the raised cylinder at the bottom of the throttle

control handle (8), and the 2 clamp gear(s) on clamp

ring for xing throttle handle (27). (See Fig. B3)

4) Clamp and make sure the raised cylinder at the

bottom of the throttle control handle (8), and the

2 clamp gear(s) on clamp ring for xing throttle

handle (27) bite each other tightly. Secure the

throttle control handle (8) by turning it in a

clockwise direction until the lock knob (26) tightens

securely. (See Fig. B4)

5) To adjust the position of the throttle control handle

(8), rst loosen but do not remove the lock knob

(26) by turning it in an anti-clockwise direction, then

slide the clamp ring forwards or backwards along

the upper blow tube (5). Tighten the lock knob

(26) to lock the throttle handle (8) in the required

position. (See Fig. B5, B6)

B1.

B2.

B6.B5.B4.

B3.

51.7cc 2 Stroke Petrol Backpack Blower

AFTER SALES SUPPORT

e-mail: info.aldi@positecgroup.com

1300 889 028

MODEL: №. SBV521 • 02/2020 • 13177

(toll free)

Assembling the upper blow tube (5) to the

exible pipe (4)

1) With the throttle control handle (8) now

secured to the upper blow tube (5), insert the

end of the upper blow tube (5) with raised

ridges on it into the exible pipe (4) to the end,

until the end of the exible pipe (4) hits the

raised ridges of the upper blow tube (5). (See

Fig. C1)

2) Secure the other adjustable clamp on the

exible pipe (4) using the supplied slot end of

the combination screwdriver (32) by turning

the screw on the clamp in a clockwise direction

until tight. (See Fig. C2)

Fixing the throttle cable (13)

1) Find the xing clip for the throttle cable (14)

hooked onto the exible pipe (4). (See Fig. D1)

2) Fit the throttle cable (13) into the xing clip

(14). (See Fig. D2)

Assembling the Middle & Lower Blow Tubes

(6/7)

1) To attach the middle blow tube (6), rstly

loosen the assembly screw by turning it in an

anti-clockwise direction using the supplied

philips end of the combination screwdriver

(32) until the screw end is sitting ush on the

internal side of the middle blow tube (6). (See

Fig. E1)

2) Align the 2 raised locking pins on each side of

the end of the upper blow tube (5) with the 2

channels on the middle blow tube (6). Push the

tubes together, insert the middle blow tube (6)

to the end until it cannot be pushed anymore.

Rotate the middle blow tube (6) clockwise to

the end (about 90 degrees). You will feel the

tubes engage if done correctly. (See Fig. E2)

D2.

D1.

C2.

C1.

AFTER SALES SUPPORT

(toll free)

e-mail: info.aldi@positecgroup.com1300 889 028

51.7cc 2 Stroke Petrol Backpack Blower

MODEL: №. SBV521 • 02/2020 • 13177

3) Tighten the assembly screw using the supplied philips end of the

combination screwdriver (32) in a clockwise direction until tight. (See Fig.

E3)

4) To attach the lower blow tube (7), rstly loosen the assembly screw by

turning it in an anti-clockwise direction using the supplied philips end of

the combination screwdriver (32) until the screw end is sitting ush on

the internal side of the lower blow tube (7). (See Fig. E4)

5) Align the 2 raised locking pins on each side of the end of the middle

blow tube (6) with the 2 channels on the lower blow tube (7). Push the

tubes together, insert the lower blow tube (7) to the end until it cannot

be pushed anymore. Rotate the lower blow tube (7) clockwise to the end

(about 90 degrees). You will feel the tubes engage if done correctly. (See

Fig. E5)

6) Tighten the assembly screw using the supplied philips end of the

combination screwdriver (32) in a clockwise direction until tight. (See Fig.

E6)

E1.

E2. E3.

E4.

E5. E6.

51.7cc 2 Stroke Petrol Backpack Blower

AFTER SALES SUPPORT

e-mail: info.aldi@positecgroup.com

1300 889 028

MODEL: №. SBV521 • 02/2020 • 13177

(toll free)

Alternative variation of the blow tube assembly

The previous assembly details using all 3 tubes on the Petrol Backpack

Blower (See Fig. F1).

If your task does not require the blow tube assembly to be this long, the

below variation can also be used:

1) Assemble only the upper (5) and middle (6) blow tubes, and no need to

assemble the lower blow tube (7) (See Fig. F2).

F2.F1.

AFTER SALES SUPPORT

(toll free)

e-mail: info.aldi@positecgroup.com1300 889 028

51.7cc 2 Stroke Petrol Backpack Blower

MODEL: №. SBV521 • 02/2020 • 13177

Prepare the fuel mixture

This product is powered by a 2-stroke engine and requires the pre-mixing of

fresh unleaded fuel with 2-stroke oil.

WARNING:

• Using fuel alone will damage the engine quickly.

• When mixing fuel and oil it is recommended to wear eye protection,

and to mix in a well ventilated location.

• Fuel mixture are highly inammable!

• Keep the fuel mixture in an approved container, in a safe place,

away from any ames or heat sources or reach of children.

• Never smoke whilst preparing the mixture and avoid inhaling the

fuel fumes.

IMPORTANT:

• Use only fresh unleaded fuel with a fuel grade of at least 90 ON, and only

use top quality synthetic oil specically for 2-stroke engines to maintain

high performance and guarantee the duration of the mechanical parts

over time. Do not use ethanol based fuels.

• Unleaded fuel tends to create deposits in the container if preserved for

more than 2 months. ALWAYS use fresh fuel.

• Do not use raw fuel, it will severely damage the engine very quickly.

• Do not run the tank dry at high speed, as this may cause damage to the

engine.

• Do not use oil meant for 4-stroke engines, it will cause spark plug

fouling, exhaust blocking and piston ring sticking.

• Do not use fuel mixtures that have been left standing for one month

or more, they can cause clogging of the carburettor. Do not prepare

excessive amounts of the fuel mixture.

• Keep the fuel mixture containers separate and easily identiable to

avoid the mistake of using one in place of the other.

• Periodically clean the fuel mixture containers to remove any eventual

deposits.

Preparation

51.7cc 2 Stroke Petrol Backpack Blower

AFTER SALES SUPPORT

e-mail: info.aldi@positecgroup.com

1300 889 028

MODEL: №. SBV521 • 02/2020 • 13177

(toll free)

Mixing fuel and oil (40:1 mixing ratio)

The recommended mixing ratio is FUEL: 40, OIL: 1.

40 parts fuel 1 part 2-stroke oil mix

1 litre fuel 25ml 2-stroke oil

5 litres fuel 125ml 2-stroke oil

1) Use fresh unleaded fuel and a good grade of 2-stroke oil for 2-stroke

engines.

NOTE: Mix the fuel and oil in an approved container. Never mix fuel

mixture directly in the blower fuel tank (12). A fuel/oil mixing bottle (30)

is provided with this blower. (See Fig. G1)

2) Place the supplied plastic fuel/oil mixing bottle (30) on a level surface.

Fill with fresh unleaded fuel in the bottle (30) to the top 500 marking

shown on the outside surface of the bottle (30), then ll with 2-stroke oil

to the 40:1 oil marking. (See Fig. G2)

3) Shake the bottle (30) to mix the fuel and oil thoroughly and also each

time before fuelling.

4) Always pre-mix in small quantities. Never mix quantities larger than

what will be used in a 30-day period.

NOTE: The fuel/oil mixing bottle (30) provided is NOT for the storage

of fuel. This bottle (30) is solely for mixing of fuel and oil only. Ensure to

keep the bottle (30) in a safe storage location, empty of fuel and out of

reach of children.

G1.

40:1

2 STROKE OIL

500ml

FUEL

G2.

AFTER SALES SUPPORT

(toll free)

e-mail: info.aldi@positecgroup.com1300 889 028

51.7cc 2 Stroke Petrol Backpack Blower

MODEL: №. SBV521 • 02/2020 • 13177

Fuelling

IMPORTANT: Fuel goes o after about 3-4 months. If

you nd your unit does not start, rst change the fuel

in the tank with newly purchased fuel.

WARNING! Do not rell fuel tank while

engine is running or is hot.

Move at least 15m away from the refuelling site

before starting engine.

1) Place the blower on a secure surface, or on the

ground in the upright position. Clean the fuel tank cap (11) and the

surrounding area to avoid any dirt from entering

the fuel tank (12) during fuelling.

NOTE: Be careful not to spill any mixture. If this

happens, wipe the spill with clean cloth.

2) Unscrew the fuel tank cap (11) carefully and pour

an amount of fuel/oil mixture suited to the work to

be performed into the fuel tank (12). (See Fig. H1,

H2)

3) Re-t the fuel tank cap (11) onto the fuel tank (12),

tighten it rmly in a clockwise direction.

4) Do not overll. Leave a minimum 5mm of space between the top of

the fuel/oil mixture and the inside edge of the fuel tank (12) to allow for

expansion.

WARNING! Always close the fuel tank cap rmly.

Immediately clean all traces of fuel which may have dripped on the

machine or the ground and do not start the engine until the fuel fumes

have dissipated.

NOTE:

• Do not use fuel that contains ethanol. Use fresh unleaded fuel.

• Do not smoke when refuelling or operating the product.

• Be careful not to admit dust, dirt, water or other foreign objects into the

fuel.

• Wipe o spilt fuel thoroughly before starting engine.

• Always use extreme care when handling fuel! Fuel is highly ammable.

• Never attempt to fuel the product if the fuel system components are

damaged or are leaking.

• Never attempt to refuel the engine while it is running or still warm,

allow it to cool before fuelling.

H1.

H2.

51.7cc 2 Stroke Petrol Backpack Blower

AFTER SALES SUPPORT

e-mail: info.aldi@positecgroup.com

1300 889 028

MODEL: №. SBV521 • 02/2020 • 13177

(toll free)

• Never smoke or light any res near the product or fuels.

• Danger of re and burn injuries.

• Always transport and store fuels in an approved container.

• Never place ammable material close to the engine muer.

• Do not use fuel which contains ethanol or methanol as it may damage

the fuel lines and other engine parts.

Adjusting the angle of the throttle control handle (8)

The throttle control handle (8) can be positioned with dierent angles as

required.

1) Loosen the lock knob for xing throttle handle (26) by turning it in an

anti-clockwise direction. Do not remove the lock knob (26) away. (See

Fig. I1)

2) Rotate the throttle control handle (8) clockwise or anti-clockwise to

acquire the required angle. (See Fig. I2, I3)

3) Secure the throttle control handle (8) at the required angle by turning

the lock knob (26) in a clockwise direction until it tightens.

I1.

I3.

I2.

AFTER SALES SUPPORT

(toll free)

e-mail: info.aldi@positecgroup.com1300 889 028

51.7cc 2 Stroke Petrol Backpack Blower

MODEL: №. SBV521 • 02/2020 • 13177

Operation

WARNING: This blower is not suitable for use

for children below the age of 14 years old.

Children below the age of 14 years old should not

use, or be in reach of this blower during its

operation.

During operation of the blower it is recommended

to wear eye protection, a dust mask, and full

hearing protection. Ensure you are wearing suitable

clothing, no loose jewellery, and be cautious of hair

entanglement. Long hair should be suitably protected.

Choke control

If the engine is cold you will need to use the choke

control.

Start position (choke closed) (See Fig. J1)

Run position (choke open) (See Fig. J2)

Starting the blower

WARNING: Before beginning the starting operation, place the

blower on a sturdy surface sitting upright. DO NOT start the

blower with the unit already placed on the user’s back.

- Cold engine starting

A “cold engine starting” means before starting, the blower is not used up for

at least 10 minutes.

1) Push the stop/start/MAX speed lever (16) downwards to the start position

as indicated by an "I" in Fig K1.

NOTE: The marked position "I" and position "MAX" as indicated in Fig. K1are

for the use of adjusting the blower speed. Details refer to Adjusting the

blower speed section.

2) Turn the choke knob (10) clockwise to "Start" position. (See Fig. J1)

3) Press the primer bulb (23) 7 to 10 times to prime the carburettor. (See Fig. K2)

J1.

J2.

51.7cc 2 Stroke Petrol Backpack Blower

AFTER SALES SUPPORT

e-mail: info.aldi@positecgroup.com

1300 889 028

MODEL: №. SBV521 • 02/2020 • 13177

(toll free)

4) Sit the blower upright on the ground. Hold

the blower rmly with one hand on the carry

handle (1), securing the blower on the ground,

in order not to lose control of the blower

during starting. (See Fig. K3)

5) Firmly hold the recoil starter (24) with the other

hand and pull it out slowly for 10-15cm until

resistance is felt, then pull it hard rapidly until

the rst engagement is heard. (See Fig. K3)

IMPORTANT: To avoid breaking the starter

rope, do not pull the whole length of it. Release

the starter gradually, to avoid letting it y back

uncontrollably.

6) Turn the choke knob (10) anti-clockwise to

"Run" position. (See Fig. J2)

7) Pull the recoil starter (24) again until the engine

starts.

NOTE: Allow the engine run at idle for 10

seconds after engine starts.

8) Squeeze the throttle trigger (15) slightly to

release the throttle lock and warm the engine

up before using the blower. (See Fig. K4)

9) Now the blower is ready for placing on the

user's back with shoulder straps. Refer to Fitting

& adjusting the shoulder straps.

- Hot engine starting

A “hot engine starting” means to start the blower

immediately after it is just switched o.

1) Push the stop/start/MAX speed lever (16)

downwards to the start position as indicated by

an "I" in Fig K1.

2) Press the primer bulb (23) 7 to 10 times to

prime the carburettor. (See Fig. K2)

3) Sit the blower upright on the ground. Hold

the blower rmly with one hand on the carry

handle (1), securing the blower on the ground.

(See Fig. K3)

K1.

K3.

K2.

X 10

K4.

AFTER SALES SUPPORT

(toll free)

e-mail: info.aldi@positecgroup.com1300 889 028

51.7cc 2 Stroke Petrol Backpack Blower

MODEL: №. SBV521 • 02/2020 • 13177

4) Turn the choke knob (10) anti-clockwise to "Run" position. (See Fig. J2)

5) Firmly hold the recoil starter (24) with the other hand and pull it out

slowly until resistance is felt, then pull it hard rapidly until the engine

starts. (See Fig. K3)

6) Squeeze the throttle trigger (15) slightly to release the throttle lock.

7) Now the blower is ready for placing on the user's back with shoulder

straps. Refer to Fitting & adjusting the shoulder straps.

Adjusting the blower speed

The blower speed must be proportionate to the type of work.

- To adjust by controlling the throttle trigger (15) (See Fig. L1)

If you want to adjust the speed at any time by

yourself, you can control the blower speed by

adjusting the throttle trigger (15) located on the

throttle control handle (8).

1) While working, keep the stop/start/MAX speed

lever (16) at the start position as indicated by an

"I" in Fig K1, and push in the throttle trigger (15)

continuously, the blower speed will increase with

pressure. Slowly release the throttle trigger (15) to

decrease the blower speed.

- To adjust by controlling the stop/start/MAX speed lever (16) (See Fig. L2)

If you do not want to always putting your ngers

on the trigger (15), you can also control the blower

speed by only adjusting the stop/start/MAX speed

lever (16). In this way you can free your hands and let

the blower control the speed itself.

1) Place the stop/start/MAX speed lever (16) at the

start position as indicated by an "I" in Fig K1. Then

continue to push the speed lever (16) downwards

slowly to the lowest position "MAX" as indicated in

Fig. L2. The blower speed will increase and achieve

to the maximum speed when the stop/start/MAX speed lever (16) is

placed exactly at the "MAX" position.

NOTE: While adjusting the speed lever (16) from position "I" to "MAX",

the throttle trigger (15) will be automatically depressed to the end. You

can disregard it since at this time the trigger (16) will no longer aect the

speed adjustment when the stop/start/MAX speed lever (16) is put in the

"MAX" position.

L1.

L2.

51.7cc 2 Stroke Petrol Backpack Blower

AFTER SALES SUPPORT

e-mail: info.aldi@positecgroup.com

1300 889 028

MODEL: №. SBV521 • 02/2020 • 13177

(toll free)

Stopping the blower

IMPORTANT: Remove the blower from your back and place on a level

ground surface before stopping the blower.

To stop the engine:

– Push the stop/start lever (16) downwards to the

start position as indicated by an "I" in Fig K1.

– Release the throttle trigger (15), allow the engine

run at idle for 10 seconds.

– Turn the stop/start/MAX speed lever (16) upwards

to the highest "O" position. (See Fig. M)

Emergency stopping

In the event the blower engine does not stop, the following processes will

assist.

WARNING: Remove the blower from your back and place on a

level ground surface. NEVER move the blower, or attempt to

move the blower if the controls DO NOT turn o the engine.

1) In the event the controls do not turn o the engine, press the primer

bulb fully approximately 10 times or continue to push the primer until

the engine stalls.

2) If this fails to stop the engine, remove the spark plug cover from the

spark plug.

IMPORTANT:

• If the spark plug method is used, it is recommended to wear a rubber

glove when grasping the spark plug cover.

• Persons with heart conditions or any medical condition which can be

aected by electric shock should not attempt this method.

3) NOTE: If the above methods do not stop the blower, let the blower

continue to run until the tank runs out of fuel.

– DO NOT Panic.

– DO NOT leave the blower unattended if the run down method is used.

Call Customer Service on 1300 889 028.

AFTER SALES SUPPORT

(toll free)

e-mail: info.aldi@positecgroup.com1300 889 028

51.7cc 2 Stroke Petrol Backpack Blower

MODEL: №. SBV521 • 02/2020 • 13177

Fitting & adjusting the shoulder straps (2)

1) Ensuring the straps (2) are not tangled or crossing over, connect the clip

at the end of each shoulder strap (2) onto the shoulder strap connection

point(s) (29) located on each side of the blower respectively, on the

bottom of the plastic harness (21) at the rear of the blower. (See Fig. N1)

2) It is recommended to extend the shoulder straps (2) to their full length by

using the adjustment tab before putting the blower on your back, then

the tabs only need to be tightened to t. (See Fig. N2)

3) Place the shoulder straps (2) over each shoulder so that the 2 padded

shoulder straps (2) are located on your front side. The padded harness

(22) is secure against the middle of your back, and the top of the plastic

harness (21) is resting on your shoulder blades. (See Fig. N3)

Blowing

Start the blower engine, as previously described. Carry the blower on your

back, hold and control the blower tube rmly with one hand about 10–

20cm from the ground and move it in a sweeping motion from left to right,

directing the debris to the desired location.

• Use low throttle settings when clearing lightweight materials from

around lawns or shrubbery.

• Use medium to higher throttle settings to move lightweight grass or

leaves from driveways or paths.

• Use full throttle when moving heavy loads such as dirt.

IMPORTANT:

• Blower noise increases at higher throttle settings.

• Always use the lowest throttle setting required to get the job done.

• Never operate the blower unless it is properly assembled and in good

N1. N3.N2.

51.7cc 2 Stroke Petrol Backpack Blower

AFTER SALES SUPPORT

e-mail: info.aldi@positecgroup.com

1300 889 028

MODEL: №. SBV521 • 02/2020 • 13177

(toll free)

working condition.

• Never operate the blower without a properly functioning muer.

Use of the Petrol Backpack Blower

• The Petrol Backpack Blower can eciently move a wide variety of

debris ranging from grass clippings to gravel. As a general rule try to

operate the blower at the lowest throttle setting necessary to get the

job done.

• Prior to use of the blower ensure you have read and understood this

instruction manual.

• Ensure you are wearing suitable clothing, no loose jewellery, and

also safety equipment like safety glasses, ear protection and a mask

if necessary. Be cautious of hair entanglement. Long hair should be

suitably protected.

• Keep a gap between the air intake and clothing and body parts as

blocking the intake will reduce the performance of the blower and

may result in injury.

• Be aware of any local or national restrictions when using this appliance.

This could include, but not restricted to, times of operation, location of

operation, or work place operation.

• If necessary, dampen the surface to be cleaned in order to avoid

creating too much dust.

• It is recommended to use a rake or broom to loosen debris before

blowing.

WARNING: Always pay the utmost attention to prevent removed

material or dust from injuring people or animals or damaging

property. Always pay attention to the wind direction and never work

against the wind.

AFTER SALES SUPPORT

(toll free)

e-mail: info.aldi@positecgroup.com1300 889 028

51.7cc 2 Stroke Petrol Backpack Blower

MODEL: №. SBV521 • 02/2020 • 13177

Maintenance

WARNING: Before performing any maintenance on this blower,

stop the engine, wait until the engine is suciently cold, and

disconnect the spark plug (25).

Checking the spark plug (25)

Periodically check the spark plug (25) every 10-15 hours of use.

1) Remove the black spark plug cover (9) on the spark plug (25). (See Fig. O1)

2) Use the supplied socket spanner for spark plug (31) to remove the spark

plug (25), by turning it anti-clockwise (See Fig. O2)

3) Clean the spark plug using a metal brush to get rid of any deposits.

Check and adjust the spark plug gap to 0.6 - 0.7mm. (See Fig. O3)

4) Re-install the spark plug (25) onto the blower head, then tighten it rmly

with the supplied socket spanner for spark plug (31).

5) Replace any damaged or visibly worn spark plug (25), or in any case every

100 working hours, with the same characteristics of the new spark plug (25).

* Replacement spark plugs are available from purchase from lawn mower

or small engine repair shops.

O1.

O2.

O3.

0.6 - 0.7mm

51.7cc 2 Stroke Petrol Backpack Blower

AFTER SALES SUPPORT

e-mail: info.aldi@positecgroup.com

1300 889 028

MODEL: №. SBV521 • 02/2020 • 13177

(toll free)

Air lter (19)

IMPORTANT: The air lter (19) should be checked

approximately every 8-10 hours of use, or more

frequently in dusty areas. Cleaning the air lter (19)

is essential to guarantee the eciency and duration

of the blower. Do not work with a damaged lter or

without a lter, as this could permanently damage

the engine.

1. Loosen the air lter locking knob (18) by turning

it in an anti-clockwise direction. Remove the air

lter cover (17). (See Fig. P1)

2. Remove and inspect the sponge lter. If the

sponge lter is distorted or damaged, replace it

with a new one. (See Fig. P2)

3. Wash the sponge lter with soap and water. Rinse

it thoroughly. Squeeze out excess water. Leave

it to dry completely in the open air before re-

installing. Do not use petrol or other solvents.

4. Re-install the sponge lter and then re-t the air

lter cover (17). Tighten the air lter locking knobs (18) in a clockwise

direction.

After use

• When you nish working, clean the Petrol Backpack Blower

completely.

• Inspect the entire blower, the tubes, the cylinder, the recoil starter

rope, all the nuts and screws for damage, including any loose or

missing components, and repair anything necessary.

Servicing

• It is recommended once you rst use your Petrol Backpack Blower,

have it serviced after 15 hours of use.

• From thereafter, service the Petrol Backpack Blower every 2 years.

P1.

Loosen

Tighten

P2.

AFTER SALES SUPPORT

(toll free)

e-mail: info.aldi@positecgroup.com1300 889 028

51.7cc 2 Stroke Petrol Backpack Blower

MODEL: №. SBV521 • 02/2020 • 13177

Maintenance timescale

* Recommends that this work should be done by a Service Agent or qualied persons.

Periodic maintenance

The following intervals apply

to normal operating conditions

only. If your daily working time

is longer or operating conditions

are dicult (very dusty work

area, etc.) shorten the specied

intervals accordingly.

Before starting

working

After nishing

work daily

After each

refueling stop

Weekly

Monthly

Every 12 months

If problem

If damaged

If required

Whole

machine

Visual

inspection

(condition,

wear, leaks)

Clean

Throttle

handle

Check operation

Air lter Clean

Replace

Fuel lter

(Inside the fuel

tank)

Check

Replace*

Carburettor Check idle

setting

Readjust idle*

Spark plug Clean and

re-adjust the

gap every 10

working hours

Replace after

100 hours of

operation

Cooling inlets Clean

All accessible

screws

Check

Re-tighten

Anti-vibration

elements

Check

Replace*

Muer Clean*

51.7cc 2 Stroke Petrol Backpack Blower

AFTER SALES SUPPORT

e-mail: info.aldi@positecgroup.com

1300 889 028

MODEL: №. SBV521 • 02/2020 • 13177

(toll free)

Storage and Transportation

• Store the blower away from direct sunlight.

• Use a small brush to clean o the outside of the unit and keep the air

vents free from obstructions. Do not use water or a hose to clean the

unit.

• It is recommended to drain the fuel from the blower on the completion

of use, prior to storage or transportation.

Whenever the machine is not used for a long period of time, proceed as

follows:

• Give the blower an overall cleaning and a thorough check.

• Empty the fuel tank (12) completely, then clean the carburettor and

lines by running the blower until it stops from lack of fuel.

• Protect all metal engine parts from corrosion by coating them with oil.

• Remove the spark plug (25), put several drops of oil into the cylinder

through the spark plug hole and then pull the recoil starter (24) 2 to 3

times in order to distribute the oil evenly. Replace the spark plug (25)

and spark plug cover (9).

• Clean the air lter (19) as described in the Air lter (19) section.

For transporting the blower it is recommended to disassemble the product

and put it back inside its original packaging (or the like), to prevent any

damage during transit. Ensure the fuel cap is secured tightly to avoid fuel

leakage.

Environmental protection

Recycle unwanted materials instead of disposing of them as waste. All

tools, hoses and packaging should be sorted, taken to the local

recycling centre and disposed of in an environmentally safe way.

Dispose of used motor oil in a manner that is compatible with the environ-

ment. We suggest you take it in a sealed container to your local service station.

AFTER SALES SUPPORT

(toll free)

e-mail: info.aldi@positecgroup.com1300 889 028

51.7cc 2 Stroke Petrol Backpack Blower

MODEL: №. SBV521 • 02/2020 • 13177

tion for reclamation. Do not throw it in the trash or pour it into the earth.

Noise and Vibration

Noise information

A weighted sound pressure L

=100.7 dB(A)

= 3 dB(A)

A weighted sound power L

=113 dB(A)

= 3 dB(A)

wear ear protection.

Vibration information

Vibration emission value: a

= 2.21 m/s

Uncertainty K = 1.5 m/s²

Vibration white nger may occur in operators using handheld vibrating

tools such as blower. Continual vibration can cause both vascular damage

and also nerve damage to the operator.

The following guidelines can reduce the risk:

- Limit the use of vibrating tools.

- Hold vibrating tools as loosely as possible and in varying positions.

- Ensure tools are well maintained and replace worn parts.

- Use tools correctly, and use the right tool for the job (to do the job more

quickly and reduce exposure time).

- Use anti-vibration gloves.

- Take regular breaks of at least 10 minutes every hour away from the tool,

for both vibration and damage to the ears.

51.7cc 2 Stroke Petrol Backpack Blower

AFTER SALES SUPPORT

e-mail: info.aldi@positecgroup.com

1300 889 028

MODEL: №. SBV521 • 02/2020 • 13177

(toll free)

Warranty

Your new FERREX® 51.7cc 2 Stroke Petrol Backpack Blower will more than

satisfy your expectations.

It has been manufactured under stringent FERREX® Quality Standards to

meet superior performance criteria.

You will nd your new 51.7cc 2 Stroke Petrol Backpack Blower easy and safe

to operate, and, with proper care, it will give you many years of dependable

service.

CAUTION. Carefully read through this entire instruction manual before using

your new FERREX® 51.7cc 2 Stroke Petrol Backpack Blower. Take special care

to heed the Cautions and Warnings.

Your FERREX® 51.7cc 2 Stroke Petrol Backpack Blower has many features that

will make your job faster and easier. Safety, performance, and dependability

have been given top priority in the development of this 51.7cc 2 Stroke Pet-

rol Backpack Blower, making it easy to maintain and operate.

Use only FERREX® replacement parts for your product. Non-conforming

parts or modications made to parts will void your warranty.

What your 5 year warranty means

Great care has gone into the manufacture of this product and it should

therefore provide you with years of good service when used properly.

In the event of product failure within its intended use over the course of as

quickly as possible once it has been brought to our attention. In the un-

likely event of such an occurrence, or if you require any information about

the product please contact us via our after sales support services, details of

which can be found in this manual and on the product itself.

After Sales Support TEL: 1300 889 028

Service Support

If you have any issues with the operation of your product, please call our

Customer Service on 1300 889 028 for advice, or email us at

info.aldi@positecgroup.com

AFTER SALES SUPPORT

(toll free)

e-mail: info.aldi@positecgroup.com1300 889 028

51.7cc 2 Stroke Petrol Backpack Blower

MODEL: №. SBV521 • 02/2020 • 13177

Accessories and After Sales Parts

Accessories and after sales parts are available for purchase by visiting

https://help.tools/ or calling our customer service hotline on: 1300 889 028

Q1.

Q2.

Air Filter (13177-AF)

2. Recoil Starter (13177-RS)

51.7cc 2 Stroke Petrol Backpack Blower

AFTER SALES SUPPORT

e-mail: info.aldi@positecgroup.com

1300 889 028

MODEL: №. SBV521 • 02/2020 • 13177

(toll free)

Troubleshooting

PROBLEM POSSIBLE CAUSE REMEDY

The engine does

not start or run

irregularly.

Incorrect starting

procedure

Refer to Starting the Blower section

to re-start the blower.

Dirty spark plug or

incorrect gap between

the electrodes

Refer to Checking the spark plug

section to check, adjust or replace

the spark plug.

Air lter clogged Refer to Air lter section to clean or

replace the lter.

Carburation problems Contact Customer Service.

Blower tube not tted Refer to Assembly section to t the

blower tube.

The engine starts

but is lacking in

power

Air lter clogged Refer to Air lter section to clean or

replace the lter.

Carburation problems Contact Customer Service.

The engine makes

too much smoke

Incorrect composition

of the fuel mixture

Refer to Mixing fuel and oil section

to prepare the fuel mixture.

Carburation problems Contact Customer Service.

The machine

starts to vibrate

abnormally

Damaged or loose

components.

Stop the machine and disconnect

the spark plug cable. Inspect for

damage. Check and tighten any

loose parts. Have all checking, repair

work and replacements carried out

by a specialized person only.

For further inquiries or issues associated with your blower, call our Customer

Service on 1300 889 028 or email us at

info.aldi@positecgroup.com

AFTER SALES SUPPORT

(toll free)

e-mail: info.aldi@positecgroup.com1300 889 028

51.7cc 2 Stroke Petrol Backpack Blower

MODEL: №. SBV521 • 02/2020 • 13177

Specications

Engine 2-stroke

Engine capacity 51.7 cc

Engine power 1.6 kw

Max. Engine speed 7500 /min

Min. Speed (idle speed) 3200 ± 300 /min

Engine speed at Max. power 7000 /min

Fuel tank capacity 1.3 L

Mixture ratio (fuel: 2-stroke oil ) 40 : 1

Fuel type Unleaded fuel

Oil Type 2-stroke engine oil

Spark plug RCJ7Y

Product Dimensions 1635 x 480 x 475 mm (L x W x H)

Machine weight

(with all accessories, empty tank)

9.5 kg

This product complies with Safety: EN15503: 2009+A2: 2015

EMC: EN ISO 14982

51.7cc 2 Stroke Petrol Backpack Blower

AFTER SALES SUPPORT

e-mail: info.aldi@positecgroup.com

1300 889 028

MODEL: №. SBV521 • 02/2020 • 13177

(toll free)

MODEL: №. SBV521 • 02/2020 • 13177

1300 889 028 (toll free)

e-mail: info.aldi@positecgroup.com

ALDI guarantees that our exclusive brand products are developed to

our stringent quality specications. If you are not entirely satised with this

product, please return it to your nearest ALDI store, within 60 days from

the date of purchase, for a full refund or replacement, or take advantage of

our after sales support by calling the supplier’s Customer Service Hotline.

Made in China

FERREX® is a registered trademark of ALDI Stores

DISTRIBUTED BY:

ALDI STORES

1 SARGENTS ROAD

MINCHINBURY NSW 2770

www.aldi.com.au

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferrex SBV521 in the language / languages: English as an attachment in your email.

The manual is 5,99 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferrex SBV521 Manual

Product: