Manual Ferrex SBC52 (page 15 of 44) (English)

724593

Zoom out

Zoom in

1/44

AFTER SALES SUPPORT

(toll free)

e-mail: info.aldi@positecgroup.com1300 889 028

MODEL: №. SBC52 • 02/2020 • 700710

52cc 2 Stroke Brushcutter / Line Trimmer

Connecting the P handle to the Upper shaft

WARNING. The P handle must be tted before use of this product.

This includes both combinations of the Brushcutter or the Line

Trimmer. Ensure the motor is NOT operating when tting or adjusting the

P handle.

NOTE: Always ensure the engine is turned o before undertaking this task.

The P handle assembly consists of an upper and a lower clamp, and 4 x hex

bolts, 4

nuts & 8

washers.

NOTE: The P handle (12) should only be tted on

the upper shaft where the P handle hole (44) on the

underside of the shaft ts with the pin on the internal

side of the P handle lower clamp (12)

1. Lay the unit down so the fuel tank bracket (39) is

resting on a secure / stable surface.

2. Loosen and remove the 4 nuts from the 4 x 5mm

hex bolts for P handle (46), and place the 4 nuts

into the 4 holes on the underside of the P handle

(12) lower clamp. (Fig. D)

3. Locate the P handle middle clamp (45) next to the

P handle hole (44) on the upper shaft, and place

the P handle lower clamp such that the pin aligns

with the P handle hole (44), and the middle clamp

aligns to t inside the P handle lower clamp. (Fig. E)

4. Place the P handle lower clamp over the

underside of the P handle middle clamp (45) so

that the pin engages in the P handle hole (44),

and the lower clamp aligns with the P handle

middle clamp (45). (Fig. E)

5. Place the P handle upper clamp over the lower

P handle clamp, place the 4 x 5mm hex bolts

with washers into the 4 aligned holes of P handle

upper clamp and lower clamp. (Fig. F)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferrex SBC52 in the language / languages: English as an attachment in your email.

The manual is 6,38 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferrex SBC52 Manual

Product: