724604
38
Zoom out
Zoom in
Previous page
1/40
Next page
45cc Petrol Chainsaw
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. 53942 • 09/2018 • PM2006H
(toll free)
36
10848
.
10/2019
.
PM2006H
1300 889 028
info.aldi@positecgroup.com
Problem
Possible Cause Solution
Engine will not start No spark in the spark plug (17)
Flooded engine
Clean the spark plug (17).
Replace the old spark plug (17) with a
new one.
With the on/o switch (4) o, remove spark
plug (17) from the engine. Move combina-
tion choke control / throttle lock knob (10)
inwards, and pull the recoil starter (11) 15
to 20 times. This will clear excess fuel from
engine. Clean and reinstall spark plug (17),
and air lter cover (15). Lift the on/o switch
(4) to the “On position. Pull the recoil starter
(11) three times with choke control (10) at
RUN. If engine does not start, move choke
control (10) to CHOKE and repeat normal
starting procedure.
If engine still fails to start, repeat procedure
with a new spark plug (17).
Engine starts but will
not accelerate
properly.
Carburettor requires adjustment.
Chain brake (13) is engaged.
Refer to page 23 for adjustment, however,
It is recommended this adjustment is per-
formed by a Service Agent.
Release chain brake (13).
Engine does not reach
full speed and/
or emits excessive
smoke
Check oil / fuel mixture
Air filter (14) is dirty
Carburettor requires adjustment.
Chain brake (13) is engaged.
Use fresh fuel and the correct 2-stroke oil mix
ratio 40:1. Refer to fuel mixing section of manual.
Clean air lter (14).
Refer to page 23 for adjustment, however, It is
recommended this adjustment is performed by a
Service Agent.
Release chain brake (13).
Guide bar (19) and
chain (20) running hot
and smoking.
Chain tension too tight.
Check guide bar (19) and chain (20)
assembly.
Guide bar (19) and chain (20) are
damaged.
Re-tension the chain (20).
Refer to “Changing / Replacing of the
Guide Bar and Chain section in manual.
Inspect guide bar (19) and chain (20) for
damage.
For other issues not covered in this chart, please call Customer Service on 1300 889 028.
Troubleshooting
Troubleshooting
38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferrex PM2006H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferrex PM2006H in the language / languages: English as an attachment in your email.

The manual is 10 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info