723914
18
Zoom out
Zoom in
Previous page
1/27
Next page
Operation
18
Operation
Preselecting the oscillation rate
You can use the oscillation rate preselector
4
to adjust the speed variably between
15,000 rpm and 23,000 rpm. Level 1 represents the minimum oscillation rate; level 6
represents the maximum oscillation rate. You can adjust the oscillation rate while the
multifunction-tool is switched on.
To set the oscillation rate, turn the oscillation rate preselector to the desired level.
The required oscillation rate depends on the work material and the working
conditions and must be determined in practice.
Switching the multifunction tool on and off
To switch the multifunction tool on, push the On/Off switch
3
to position 1.
To switch the multifunction tool off, push the On/Off switch to position 0.
Working with the multifunction tool
Sawing
Only use sharp saw blades in undamaged, good condition. Bent or dull saw blades
could brake, negatively affect the cut or cause kickback.
The plunge-cut saw blade
7
and the segment saw blade
8
can be mounted at
different angles (between -90° and +90°) depending on your needs. This way, you
can avoid substantial wear of the segment saw blade along a certain edge area.
Before cutting wood, particleboard, construction materials etc. with HCS saw
blades, check for debris like nails, screws etc. Remove the debris or use saw
blades that are also suitable for cutting steel (e.g. bi-metal saw blades).
When plunge cutting, only soft materials like pine/spruce wood, gypsum cardboard or
the like may be processed.
Scraping
For best results, the scraper
10
must be sharpened regularly. Work on a soft base
(e.g. wood) at a flat angle and while applying minimal contact pressure. Otherwise,
the scraper could cut into the surface.
Select a moderate to high oscillation rate for scraping.
Sanding
Select a high oscillation rate for sanding.
Follow the instructions below for proper sanding:
Move the multifunction tool parallel and circularly over the surface or alternately
in longitudinal and transverse directions.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferrex FM 300 Multitool at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferrex FM 300 Multitool in the language / languages: English as an attachment in your email.

The manual is 0,83 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ferrex FM 300 Multitool

Ferrex FM 300 Multitool User Manual - German, Dutch - 82 pages

Ferrex FM 300 Multitool User Manual - Danish - 29 pages

Ferrex FM 300 Multitool User Manual - French - 82 pages

Ferrex FM 300 Multitool User Manual - Portuguese - 30 pages

Ferrex FM 300 Multitool User Manual - Spanish - 29 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info