764198
4
Zoom out
Zoom in
Previous page
1/60
Next page
EN
4
:DUQLQJ
 Do not use the helmet if damaged or you
suspect it may be faulty.
 Do not use helmet unless you have been
instructed in its use by a qualified person.
 Do not get the helmet wet or use in damp or
wet locations.
 Do not place the helmet on a hot surface.
,QVWUXFWLRQIRUXVH
Before using the helmet for welding
ensure you have read and understood
the safety instructions in section 2.
The helmet comes ready assembled but before
it can be used it must be adjusted to fit the user
properly.
$GMXVWLQJWKHILWRIWKHKHOPHW
Fig. 1
The overall circumference of the headband can
be made larger or smaller by first pushing the
knob to unlock and thereupon rotating the knob
on the back of the headband (Y) This can be done
whilst wearing the helmet and allows just the right
tension to be set to keep the helmet firmly on the
head without it being too tight.
If the headband is riding too high or too low on
your head adjust the strap which passes over the
top of your head. To do this release the end of the
band by pushing the locking pip out of the hole in
the band. Slide the two portions of the band to a
greater or lesser width as required and push the
locking pip through the nearest hole (W)
Test the fit of the headband by lifting up and
closing down the helmet a few times whilst
wearing it. If the headband moves whilst tilting re-
adjust it until it is stable.
$GMXVWLQJGLVWDQFHEHWZHHQKHOPHWDQGIDFH
Fig. 1
To adjust the distance between the helmet and
your face in the down position loosen the tilt knobs
on either side of the helmet and slide it nearer to
or further from your face. (Z) It is important that
your eyes are each the same distance from the
lens otherwise the darkening effect may appear
uneven. Re-tighten the tilt knobs when adjustment
is complete.
0DLQWHQDQFH
&OHDQLQJ
Clean helmet by wiping with a soft cloth. Clean
cartridge surfaces regularly. Do not use strong
cleaning solutions.
5HSODFLQJIURQWFRYHUOHQVVKDGHJODVVOHQV
Refer to figure 2 for replacing the front cover lens
or shade glass lens. This must be done everytime
the lens is damaged to reduce the risk of personal
injury.
)DXOWV
Should a fault occur, e.g. after wear of a part,
please contact the service address on the
warranty card.
(QYLURQPHQW
To prevent damage during transport, the
appliance is delivered in a solid packaging which
consists largely of reusable material. Therefore
please make use of options for recycling the
packaging.
:DUUDQW\
The guarantee conditions can be found on the
separately enclosed guarantee card.
The product and the user manual are subject to
change. Specifications can be changed without
further notice.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm WEA1058 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm WEA1058 in the language / languages: All languages as an attachment in your email.

The manual is 0,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info