Manual Ferm TSM1032 (page 8 of 80) (English, German, Dutch, French, Italian, Spanish)

510129

Zoom out

Zoom in

1/80

turned on again. The appliance will operate only

when you depress the green on switch.

Dust collection

To keep the work surface clean, the saw bench is

equipped with a connection for dust extraction.

You can connect your vacuum cleaner to this.

Connect the saw to a dust-collecting device

when sawing wood and check regularly if the

hoods/baffles/chutes are not constipated. Bust/

chipmaterials as lead-containing coatings and

some wood types can be harmful to one’s health.

Touching or breathing-in the dusts can cause

allergic reactions and/or lead to respiratory

infections to user or bystanders. Certain dusts,

such as oak or beech dust are considered as

carcinogenic, especially in connection with wood

treatment additives (chromate, wood preservative).

Sawing

Fig. 5

Take care to keep your hands away from

the saw blade when sawing.

When sawing proceed as follows:

• Loosen the knobs of the rip fence (A) on the

table surface.

• Set the rip fence to the correct distance.

• Re-tighten the knobs of the rip fence securely.

• Set the protective hood (C) to the appropriate

height.

• Switch on the saw bench.

• Feed the workpiece, without imposing

pressure on it, towards the saw blade. Support

the section of the workpiece that has already

passed the saw to ensure that it does not fall.

• When the rear edge of the appliance comes

close to the saw blade, use the push stick (B)

to feed the workpiece further. Use at all times

the push stick for small workpieces.

• Switch off the saw bench when you have

sawed the workpiece.

Mitre guide

Fig. 6

The mitre guide (A) allows you to place the

workpiece on the table at an angle of 45° allowing

diagonal saw cuts to be made. You can for this

purpose secure the mitre guide to the guide (B)

(Fig. 6).

5. MAINTENANCE

During maintenance and cleaning always

remove the mains plug from the socket.

Never use liquids when cleaning

electrical parts of the saw bench.

The machines have been designed to operate over a

long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon

proper machine care and regular cleaning.

Malfunctions

The electric motor becomes hot.

• The motor is being overloaded by workpieces

that are too big.

• Saw at a lower speed so that the motor can

cool down.

• The ventilation grid of the motor is blocked.

• Clean the ventilation grid

• The motor is defective.

• Please contact the service address on the

warranty card.

The appliance does not work when connected.

• The motor has been switched off by the

thermal cutout.

• Allow the applliance to cool down and switch it

on again.

• The mains connection has been broken.

• Check the mains connection for faults.

• The switch is damaged.

• Please contact the service address on the

warranty card.

It is very difficult to move the workpiece along

the saw blade in a straight line and the saw cut

is uneven.

• The saw blade is warped or blunt.

• Replace the saw blade.

• The rip fence is not properly secured.

• Clean the rip fence and secure it in the correct

way.

The workpiece starts to vibrate violently during

sawing.

• The saw blade is overheated or distorted.

• Replace the saw blade.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm TSM1032 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 6,25 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ferm TSM1032

Ferm TSM1032 User Manual - English, German, Dutch, French, Spanish - 48 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm TSM1032 Manual

Product: